I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
Hello Nordic team,
I am testing a plain CoAP telemetry upload from an nRF54L15 DK over Thread using a Raspberry Pi OTBR and NAT64 to ThingsBoard Cloud.
Hardware / software...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
Hi Nordic engineers,
I found a strange problem that NRF52840 voltage of io high level is just about 2.65v~2.71v. I am sure that the voltage mode is normal voltage mode...
Hello,
I'm attempting to solve some issues with my BMD-200 (nrf51822) not getting the SD BLE_GAP_EVT_DISCONNECTED message. I currently Don't seem to be getting this message...
Hi, I'm not able to find the memory layout of the nRF52840 without the SoftDevice. I'm working with the nRF52840-Preview-DK and the SDK v15.0.0. I don't need the SoftDevice...
Hi sir,
we use nRF 52832 with ESB protocol. and we use ACK to send payload to PTX , but we found must use the same pipe which PTX used pipe to send ACK .
so , I have two...
Hi, Okay I got my nRF52840 Dongle, plugged it in to my window 10, verified it shows up as USB device on window's Device Manger.
Checked and Red pulsating LED (LD2) was pulsing...
SDK : 15.0
Softdevice : 6.0
DK : NRF52_DK
Hi everyone,
Does anyone have a BLE example with C ++ ? (a beacon example or anything else) I would like to have the Makefile...
Hello everone,
I'm currently seeing about 10-11 uA additional IDLE current when the SPIS peripheral is enabled, but unused. In the nRF5 SDK v15.0.0, the SPIS example draws...
I was looking at the fstorage documentation for SDK 14.2.0 ( https://infocenter.nordicsemi.com/topic/com.nordic.infocenter.sdk5.v14.2.0/lib_fstorage.html?cp=4_0_1_3_51)
...
Hello Good People,
I need your help to kick of my development. I am using nRF52832 and Mesh stack. I am having problem to understand how its working. I have gone through...
Hello,
I am using a nRF51422 in my work. I am focusing on reducing system power consumption as much as possible.
At the moment I am using a system where the Client (dongle...
I was using for some time my code with FTDI USB converter to UART.
Recently I got built new boards, all with IC top marking N52832 QFABB0 1717AQ
and whilst any other board...
I would like to use PPI in order to set out pin and start a timer at the same time, from software.
I cant find a way to create an event from software that will fork a START...
Hello everyone, I'm currently writing my bachelor Thesis and need to establish an iot (preferably mqtt) connection from my pca10028 with my PC as broker (i.e. with mosquitto...
Why is AAR blocked if the Peer Manager Library (e.g. SDK12.3 see id_manager.c) uses the -softdevice SoC API- function call sd_ecb_block_encrypt() to resolve RPAs (Resolvable...
