Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Hi. I'm using the NRF-52 DK (PCA10056) with an SD card module and I'm trying to upload the FatFS example code for SDK 15. I'm using a kingston 8GB SD card and I'm unable to...
Hi all,
I develop program code based on nrf-mpu-magnetomter examples. I code the DMP and complied well . However the program is always stay an error when it starts running...
In my application an nRF52832 acts as a BLE peripheral device which is sending sensor data to an app on a mobile phone. As long as the phone is interested, notification on...
I'm trying to add buttonless DFU to the SDK's template application.
Here is my setup:
Soft Device 6.1.0
Secure Bootloader
Modified Template App (Added buttonless...
Hi,
I am using nrf52832 custom board with s132 to read data from 4 sensors using twi. i have 2 separate TWI with two different sensors on each bus. i am using nrf_drv_tw...
Hi,
I have a question with regards to the system-on sleep current of the nRF52840. This is specific to when using the bluetooth mesh and the nrf_mesh_disable() function...
Hello I am trying to connect nRF52832 development kit to use with Wireless vibration controller store.ncd.io/.../ using mesh module which is transmitting the data to the receiver...
Hi
I'm trying to combine NUS central and peripheral in a single nrf52840. Using SDK V 15.0.0 and softdevice V 6.0.0. Have added both ble_nus and ble_nus_c files and enabled...
I am trying to add Timer2 to light_switch server example. But it fails to compile with a undeclared error for NRFX_TIMER2_INST_IDX. I have set the following macros in sdk_config...
Hello all,
I plan on using the blinking LED authentication in mesh configuration, I have seen the nrf mesh app video where it is done using the app but I want to achieve...
Hello.
I am using the NRF52832 Evaluation board.
If I click the connected board of Device Manager to upload program application, nrfgo studio will be turned off without...
Hello,
I have an existing customer who has products based upon the nRF24L01+.
He would like to upgrade to the newer nRF52x series but is concerned about backwards compatibility...
Dear Nordic
I found a example using nrfx_twim_rx() to scan slaves, I was just wondering if I can use nrfx_twim_tx() to scan slave devices by send zero byte data? I use nrfx_twim_tx...
Hi,
In the BR Bluetooth (not BLE) there is a profile called OPP (object push profile) that enbled sending text messages to mobile phone with out the need to install any...
