I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi,
i use the Aead-Lib for CCM on the NRF52840. What is the best way to Check an Mac from a Message wich only has Adata (no acctual encryptet message)?
If i try to use...
Hi,
related to a previous question I posted, , we are migrating from nRF5_SDK_13.1.0_7ca7556 to nRF5_SDK_14.2.0_17b948a.
Now we have some problems with the bootloader...
The subject really says it all; why are there four GPIOs tied to P0.18 which is the nRF52840's RESET# pin?
I'm looking at the PCA10059 Schematic available in the nRF52840...
I am currently using the nRF24L01P in an application where I am using the RPD feature to determine whether a 2MHz RF channel is "available". For example, if a wifi network...
I am using nrf52832 and I am trying to interface OLED with it. I am attaching the code below and i referred that code from https://github.com/devdprj/olednrf here,
i made...
Hi All.
I have a DK52 project where a peripheral advertises and connects to a central nRF52840 ok. I based it on the multilink_central demo, so have the LED button service...
Hello!
I went through the example project "Experimental: ATT_MTU Throughput Example" provided in SDK v15.2.0 and found that there is a configuration bit in BLE_COMMON_OPTS...
When I connect to my device with an iPhone, using the nRF Connect app, I am experiencing an immediate disconnect. The part does not have time to start pairing. I have shared...
【Question】：I want to use timer+ppi+SPI(with DMA) write DAC, but now something is wrong, when timer trigger the SPI to write DAC through PPI, it can call the "spi_event_handler...
Hi,
I use UARTE peripheral when i communicate wih PC.
This code works. Send 4 bytes.
bno_tx_buf[0]=0xAA; bno_tx_buf[1]=0x01; bno_tx_buf[2]=0x00; bno_tx_buf[3]=0x01;...
After Updating my project to the Newest SDK for Thread 2.0 today I am having problems linking Problems.
My Project uses the Channel Monitor and changes the max children...
Hi all!
I'm quite new in working with BLE device and in working with MCU also so If my question look a bit silly, please dont laugh at me
I am using a nrf52832 as both...
I've just added a 4th Peripheral-role link to my project, and the RAM requirement for the SoftDevice increased by over 3kB. I'm trying to figure out whether I can reduce this...
Hello, I am trying to develop an application using the ADC of the nrf52832. For this, I have included the "nrfx_adc.h" library into my main code. When I try compiling the...
Hi, probably a simple answer to this but am struggling to find a decent answer on the web.
There is a function (below) and I would like to watch the p_adv_report. However...
