Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am starting to use FDS for saving data to flash memory. In the "flash_fds" example the macro APP_ERROR_CHECK() is used to check for errors in most of the function calls...
Hello,
I tried to send data through the proprietary radio. My devices are NRF52832. The data I would like to send is an uint8_t array:
Right before I send it out, I...
Hi everyone,
My English skill is not good, but I really want to share this problem to all developers that I spent three hours for it.
Example nRF5_SDK_for_Thread_and_Zigbee_2...
Hi!
I have questions for Nordic developers team. What capacity of network is possible with nrf52840 thread mesh? I've tried to attach large amount of nodes to mesh and...
Hi Guys,
I want to use the TWI for my mesh application in which I want to read out 2 sensors (Sensirion SHTW2 and SGCP3) and then send the sensor values over a mesh network...
Hi all,
I´m using nrf52832 with sdk 14.2.0 and softdevice s332.
I have opened and closed the eclipse. Now when I open it, it compiled and gives me this error that I did...
Hi,
I am using nRF_SDK_15.0.0?a53641 and writing a program with keil.
I am trying to read data from the acceleration sensor( LSM303DLHC ) by communication with BLENanov2...
Hello
I just started learning nrf52832 DK and run few of the examples. I wanted to start developing my own application based on the examples. Right now, I want to read...
Hello, I have some confusion about updating advertising packet dynamically.
I am using nrf52832 with SDK v12.3.0. I am sending datas from sensor in advertising packet(manuf...
Hi,
I am trying to build the ble_connectivity code "ble_connectivity/pca10040/ser_s132_uart" to test the serialization part. The scan is not working. I am using PCA10040...
18.9.13 RAM[0].POWERSET (and sections associated for other RAM sections) states:
When read, this register will return the value of the POWER register.
however the...
Dear Sir,
I was using my Rigado BMD 300 and it was working fine.
When I open the nRFGo Studio the following was the details displayed in the tool.
But sometime after...
Hi there,
I am struct for two days trying to send 6 packets of 20 bytes as central. I use ble app uart central sample from nrf5_sdk11.0 with nrf51 S130 v2.0 softdevice...
Hi,
Does anyone know how to receive voice data from Nordic 52832 remote control in embeded linux ? Does Nordic provide any package for this purpose ?
Thanks
Hi, everyone,
We are developing the project on nRF52832 chip that is built from master (multirole) and slaves modules. The master program (in our case master is multirole...
