Hi I've got my nRF8001 breakout board ready I now need the SDK in order to start developing firmware code.
I don't have any registration key, how do I get hold of it? ...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
We are working on the BLE Smart Switch. The requirements are pretty generic:
Low Power consumption
To be used by multiple smartphones within the house
The obvious...
Hi,
I want to set the TX power in a mesh proxy configuration. I have read mesh sdk2.1.1 TX power of nrf52832 , which works good for not proxy situation (e.g for light_switch_client...
Hi, I'm having troubles adding PWM in light_switch_proxy_server example in Mesh SDK v. 2.1.1.
It seems that the PWM driver and instances are not correctly enabled, looking...
Hello,
I was wondering if there are any article or tutorial I can follow to optimize code build with Segger Embedded Studio.
I was able to follow this article( https...
I need logging in almost anything I do, but I've never been able to start from an example that does not use logging and add logging. I've set the NRF_LOG_ENABLED and NRF_LOG_BACKEND_SERIAL_USES_UART...
Hi,
I am using nRF5 SDK 12.1.0.
I have read the s132_nrf52_3.0.0_migration-document.pdf and I am trying to implement the whitelist without the private addresses i.e...
Hello Everyone need your help.
I am using three nRF52840 dongles and have flashed hex file of an nRF example (Ble_Blinky). i want to know whether the hex file is really...
Hi, I am using SDK 15.0.0 and FreeRTOS 8.2.1 (from SDK 14.2.0).
I consistently get a stack overflow on the Idle task, caused by PendSVHandler in port.c
This can be easily...
Hi,
I'm using nRF52832 on nRF52 SDK v15.0 with S132v6.0. I know that 52832 support high throughput and advertising extension. We have more than 31 bytes data to put in the...
Hi,
I have created up to 5 custom services with several characteristics (4 at maximum) each one. They all use the same base UUID.
The problem I'm facing now is that when...
I am adding CLI service with my existing project developed based on ble_app_uart.
CLI Init function :
static void _cli_init(void) { ret_code_t ret;
#if CLI_OVER_UART...
Hi,
to be able to send more advertising data, i want to cyclical switch between different advertising packages. This already works so far.
Do i need to include the AD...
Hi there,
I am assessing the possibility of replacing a low-power MCU in one of our products with an nRF device.
Currently, our low-power MCU spends most of its time in...
Hi, all. I am trying to add a GPS module to the nRF52840 DK, just like what is done at this post. https://devzone.nordicsemi.com/b/blog/posts/nrf52840-long-range-demo
But...
Hello,
I want to write multiple words using the usb keyboard. I am working with usbd_hid_composite example on SDK_15.0.0_a53641a. I am able to write just a letter using...
