According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi all I just want to use UUID advertisement in solar beacon code for advertising @ 100ms interval I don't need temperature and pressure data .I also want to change type to...
Hi. I'm using the NRF-52 DK (PCA10056) with an SD card module and I'm trying to upload the FatFS example code for SDK 15. I'm using a kingston 8GB SD card and I'm unable to...
Hi all,
I develop program code based on nrf-mpu-magnetomter examples. I code the DMP and complied well . However the program is always stay an error when it starts running...
In my application an nRF52832 acts as a BLE peripheral device which is sending sensor data to an app on a mobile phone. As long as the phone is interested, notification on...
I'm trying to add buttonless DFU to the SDK's template application.
Here is my setup:
Soft Device 6.1.0
Secure Bootloader
Modified Template App (Added buttonless...
Hi,
I am using nrf52832 custom board with s132 to read data from 4 sensors using twi. i have 2 separate TWI with two different sensors on each bus. i am using nrf_drv_tw...
Hi,
I have a question with regards to the system-on sleep current of the nRF52840. This is specific to when using the bluetooth mesh and the nrf_mesh_disable() function...
Hello I am trying to connect nRF52832 development kit to use with Wireless vibration controller store.ncd.io/.../ using mesh module which is transmitting the data to the receiver...
Hi
I'm trying to combine NUS central and peripheral in a single nrf52840. Using SDK V 15.0.0 and softdevice V 6.0.0. Have added both ble_nus and ble_nus_c files and enabled...
I am trying to add Timer2 to light_switch server example. But it fails to compile with a undeclared error for NRFX_TIMER2_INST_IDX. I have set the following macros in sdk_config...
Hello all,
I plan on using the blinking LED authentication in mesh configuration, I have seen the nrf mesh app video where it is done using the app but I want to achieve...
Hello.
I am using the NRF52832 Evaluation board.
If I click the connected board of Device Manager to upload program application, nrfgo studio will be turned off without...
Hello,
I have an existing customer who has products based upon the nRF24L01+.
He would like to upgrade to the newer nRF52x series but is concerned about backwards compatibility...
Dear Nordic
I found a example using nrfx_twim_rx() to scan slaves, I was just wondering if I can use nrfx_twim_tx() to scan slave devices by send zero byte data? I use nrfx_twim_tx...
