Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Using VSCode with nRF Connect extension on Ubuntu Linux 22/04 with nRF SDK 3.0.1 and nRF Toolchain 3.0.1 installed I can create a build configuration for Zephyr's hello_world...
I get a bunch of errors like undefined reference to `mbedtls_ssl_free', `mbedtls_ssl_get_bytes_avail',`mbedtls_ssl_config_free', 'mbedtls_ssl_read'
`mbedtls_ssl_set_bio...
Hello, I did my first BLE design and it went wrong I missed some critical design requirements and I want to ensure that the next prototype performs better. The design is a...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
We want the system to be in low power mode in idle state. Therefore after advertisement is sent the BLE is switched off using bt_disable. The return for this function is fine...
Hi nordic:
Project MCU: NRF54L05; Development Platform Version: NCS 2.9.0. The APP occupies 220KB of space. adding MCUBOOT and Create an pm_static.yml file in the project...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi,
i'd like to know if I can use uart1 with non secure build. I have see this doc here , but I have try to add these configuration in my prj.conf:
And add this...
Hi,
I am currently developing an nRF54L15 module.
During the evaluation, I measured the Tx current consumption and got a result that was 2mA higher than the value listed...
Hi.
I've noticed that the Zigbee Add-on R23 has just released version 1.0.0 and is not marked experimental anymore. This is great news.
But I find that the references...
Hello, I'm trying to perform a firmware update using the FOTA feature on the nRF7002. After building and running the firmware update code, the following error occurs:
...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
Hello.
How often are the LQI and RSSI values in the coordinator updated for a child?
Preferably I would have liked to get some kind of notification every time LQI and...
