But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I'm using nRF51, SDK10, S110 beacon example with dfu service.
What I have done are listed as below:
merged softdevice8.0 and bootloader to sd_bl.hex and...
hi,
in FreeRTOSConfig.h file,
#define configUSE_TICKLESS_IDLE 1
#define configUSE_IDLE_HOOK 1
and the idlehook function
void vApplicationIdleHook( void )
{
__WFI;...
I have got PCA10040 development board having nRF52832 nordic ble chip. I am not able to get datasheet for this. I have to use SPI communication on this board but I am confused...
Hai i am new embedded designer.. I am working with nrf52832 , i need to get accelerometer and gyroscope data from mpu6050 through twi.. Can any one give me a sample code ...
I am trying to wake my processor from sleep after issuing the sd_app_evt_wait(); Using an interrupt on an external RTC chip, I send interrupt pulses to the nRF at 1Hz. At...
Hi guys,
I have two nrF51 dongles and I am really interested in making the pairing of both of them using the proximity search feature of ANT. So far what I did is, I took...
Hi.
I have a BLE peripheral app for the nRF51822. I'm using SDK 12.1.0 with SD 130 v2.0.1 and gcc. I'm implementing DFU OTA at the moment and I notice there are two builds...
Hi,
I have an old project running on nRF51822, with SoftDevice SDK v8 - S110 mode.
I'm trying to migrate the project to a nRF52832 with SoftDevice SDV v12 - S132 v3 mode...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Hello,
I am facing many communication error with code 1 when using the UART.
Everything is working fine until my client reads long characteristics (in my case it is about...
Hi
We're trying to get the BLE packet size using:-
uint32_t nrfErr;
uint8_t PacketSize;
ble_opt_t opt;
/* Get the extended length BLE option */
nrfErr = sd_ble_opt_get...
Problem:
We trigger HardFaults reproducibly. By manually unwinding the stack we have traced the source of the error back to the TIMER2_IRQHandler in Gazell.
We can see...
Hello,
I am using SDk 11.0.0 and I am trying to integrate the DFU from the heart rate example into the my code, which is based upon the BLE UART (NUS) example. When I run...
