Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hi,
I'm currently using NCS v2.9.0 under sysbuild and have recently been using board definitions from different directories. My recent projects possess a "boards" sub-directory...
Hi, I've been trying to top up my iBASIS SIM card, but after clicking on the nRF Cloud SIM "Buy data" link it fails and generates a system error message (see image below)...
Hi all,
Has anyone implemented an MQTT client on an 54L15 before? I have been searching the web and I have not seen a sample program or anyone talking about MQTT with 54L15...
Hello, I've completed nRF Connect SDK Fundamentals Certificate of Completion but I've noticed a little problem with printk and logging.
When I use build configuration with...
Hello, I have nrf5340dk and AT21CS01-STUM10-T module. This is EEPROM module. I want to communicate with it by 1-wire. The problem is that I don't know how to do it. I looked...
Hi,
I was wondering if the newest sample available in NCS3.0.1 is already capable of holding multi connections. Otherwise, for this little time that is present i will...
This may be a silly question but for the channel sounding with range requestor sample the numbers following each method is the distance in meters right? I: Distance estimates...
Hello,
I am developing custom hardware based on this DK and am trying to eliminate circuitry that is unnecessary to my application. The DK includes a U20 load switch which...
Hi, I created a blinky sample for the ProMicro board. Entered the flash mode as mentioned in https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/boards/others/promicro_nrf52840...
Hello Nordic Support Team,
I am working with the nRF54L15-DK and testing the Bluetooth Direct Advertising sample application (based on Zephyr). I am measuring current consumption...
Hello,
I am using the nRF5340DK and the PCF8574 with I2C communication. The issue I am encountering is that the function device_is_ready(pcf8574.bus) fails to initialize...
Behaviour:
Declaring a carbon dioxide attribute list with
results in
Using
results in
"zb_zcl_carbon_dioxide_measurement.h" and the macro "ZB_ZCL_CLUSTER_ID_CARBON_DIOXIDE_MEASUREMENT_CLIENT_ROLE_INIT...
Hello Nordic Team,
I am experiencing an issue when attempting to flash a Zephyr RTOS application (v3.0.0) to the Adafruit Feather nRF52840 Sense board using a J-Link debugger...
Hello,
I'm having a serious issue with my nRF52840 board. Here’s what I already tried:
What I have done:
Verified working USB cables (data + power).
Installed...
Hi,the nodic team
I use the system on mode to made the SED device into the low power,I found that in addition to my 5s polling woke up the device, there was another that...
