Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hello,
I am new on nRF51 and i would like to have a function to read the rotary position of motor in any rotary direction by adding a codewheel and a two channel reflective...
Hello,
I am trying to implement wake on motion functionality of MPU9250 with nRF52.
I am writing below sequence code for wake on motion configuration:
void MPU6500_StartMotionDetection...
Hi DevZone
I want to make a little beacon app, that advertises on channel 37 then waits 700 ms, advertises on channel 38, waits 700 and advertises on channel 39.
The below...
HI,
I wan't to read sensor data from ADC. So i use nrf_drv_saadc_sample() .
On Arduinos i usually call value = analogRead() and after that i process the data. But here the...
Hello,
We need to add custom data to advertise packet. As I understand we can use Manufacturer Specific Data. But to do this we need to get our Manufacturer ID from Bluetooth...
I have the following code for a custom service UUID and a custom 128 bit characteristic ID. I get a error of no memory available in our_char_init while adding the 128 bit...
Hi,
We bought a mac bd addr pool from IEEE
Where is the best way to store this mac adress during production ?
We guess the type will be: BLE_GAP_ADDR_TYPE_PUBLIC
Do...
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi. I'm using nRF51822, SDK12.2.0, S130.
I finally compiled bootloader_secure which was very hard.
Q1. After run bootloader, I can find the device using DFU "DfuTarg"...
Hi ,
I am trying to use the new softdevice SD130 V2.0.0 and have not had any luck when using the most recent version of SD130. I ran the same application with SD130 V1...
I've nrf51dk development board. It has nrf51422QFACA10 chip and has 32kB ram and 256kB flash. I downloaded sdk V11 and programmed ble_app_beacon_s130_pca10028. It worked fine...
I try to move my project from Keil to GCC but I get some different behavior. To show the difference I use examples/ble_peripheral/ble_app_uart
The part of the code below...
I have purchased a nRF52 DK and want to use it by emulating an ANT+ Stride Based Speed and Distance (foot pod) and pair that with my Garmin FR235 running watch in order to...
Environment:
Segger Embedded Studio
nRf51 Developementkit using jLink OB firmware
S130
We're using the \nRF5_SDK_12.2.0_f012efa\examples\ble_peripheral\ble_app_template...
