Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Hi. i'm using nRF52832, SDK13, S132v4 as multi-link peripheral.
As I know, SDK13 supports multi-link peripheral refering to example "experimental_ble_app_multiperipheral...
Hi,
I am using the nRF52832 and I have use the serial bootloader to update the firmware at one of my clients place.
Actually, I have used nRFgo Studio to flash the softdevice...
Hi
I'm setting up a firmware based on the DTM example to perform certification tests.
In the DTM example firmware I see that there is a VENDOR_SPECIFIC command option...
hi,
i tried nrf51822_beacon_app.hex( C:\Nordic Semiconductor\nRF51822 Beacon v1.1.1\Source Code\nrf51_beacon\ble_app_beacon\pca20006\s110\arm_build\ ).in that we changed...
This might not be the correct place/forum to ask this question.
Since a couple of days, I am not able to step or next with gdb .
I understand that gdb needs to know what...
Hi：
Now keil4 default is to use the 16_bit THUMB instruction set, if I want to set it to start the program using the 32_bit ARM instruction set, how should we do? thanks
Hi,
After reading some questions about these topics I became a little confused.
I want to count milliseconds, so should I use Systick_Handler or use Real Time Counter...
Edit 1
To narrow down I did this... Below is ble_dfu_init() from ble_dfu.c.
uint32_t ble_dfu_init(ble_dfu_t * p_dfu, const ble_dfu_init_t * p_dfu_init)
{
uint32_t...
I am running NUS and a custom service.
I have updated vs_uuid_count = 2 in softdevice_handler.c
Following other posts on the forum, I have stepped through the code using...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Hello everyone
I was not able to find any explicit statement regarding the use of the TWI_APP with easyDMA on the nRF52 series and SDK13.0.0.
I checked the examples...
Hello guys,
I am currently looking at the recommended schematic QFN48 with internal LDO setup and I have a few questions (sorry, if they are silly, I am a newbie).
...
Hi, I'm working on an extremely space-tight design and need some clarifications. It is an nRF52832 QFAA chip with a Johanson 2450AT18B100 chip antenna.
Up to this point...
Hi,
I would like to use higher dBi antenna instead of the DK pcb antenna. Can I say the pi-network before J1 (measurement point) probe is 50ohm? Hence I can just remove...
I am trying to control another BLE device with nRF52xx. For controlling the device I need a terminal for connecting, disconnecting and switching on & off a sensor. I have...
