When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
Hi,
for my project (its based on FreeRTOS) I was trying to reassign button actions in order to detect a long push event, what obviously doesn't work at all. In bsp.c i saw...
Basically I used below function for sending 1 byte of data with bluetooth and it is working completely fine.
static void test_service_on_ble_write(ble_os_t *p_service,...
Hi,
I need to send some data but this should be done compressed using gzip or deflate algorithms (like in http). I have been searching for some info about the possibility...
Hi,
It's my first post here so let introduce myself : I'm a 25 y.o. French electronics engineer and hobbyist. I also like skating (inline skates and ice skates) mainly...
Hi, I was trying to create an NUS (Nordic UART Service) application for iOS 10 devices using Swift 3.
I was testing with my
iPhone 6 Plus 64GB (iOS 10.2.1)
...
Hello,
I am working on nRF52832, In my application I have added base UUID, service UUID and two characteristic UUIDs.
Please send me any example code for adding two...
Hello to all embedded jedi-masters out there!
I need your guidance.
I have a general product design question: I was wondering on what would be the best practice for...
Hi,
I am facing some problem with openocd and stlink connection.
I saw some dve. boards having USB<->serial converter on board for programming (i guess).
So, i got...
Hi,
I have install openocd on ubuntu. but i after running next line
openocd -f interface/stlink-v2.cfg cfg -f target/nrf51_stlink.tcl
i got these error.
Runtime...
Hi,
I'm trying to modify one of the examples (the hrs_relay) to find my custom service to identify the device uniquely. I know I need to add the 128bit uuid using and then...
I'm trying to transmit a radio signal inside time slot handler, the code is like:
switch (signal_type)
case NRF_RADIO_CALLBACK_SIGNAL_TYPE_START:
radio_configure...
I'm working with nrf52832 dev board. I used nRF Connect app for IOS but my phone run on IOS8.4.1, so i can't get it from apple appstore. Someone can help me by give version...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
