Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I am using an nRF520 PCA10040 dev board with a nRF52832 module and I am trying to get the ble_app_uart_pca10040_s132 FW to run using the SES segger tool set. After about 1...
Still having trouble getting a simple Blinky example running on two nRF52840 DK boards configured for a long range PHY_CODED connection.
I've looked through this post -...
I am new to the Nordic SDK and Segger embedded studio, and I am trying to test my NRF52840 dev board.
I am running the "ble_app_blinky_pca10056_s140" example, and I want...
1. Background info
We're developing a new IDE for microcontrollers (see https://embeetle.com ) and would like to support a range of Nordic Semiconductor microcontrollers...
1. Intro
We're developing a new IDE for microcontrollers (see https://embeetle.com ) and would like to support a range of Nordic Semiconductor microcontrollers. We received...
Hi,
In case of nRF52810, is it possible to implement both Master and Slave Mode ?
Also, this has do be done while the product being able to work with AT Commands.
...
Power Profiler V2.3.1
Hi,
I recently started doing power testing on one of our boards using the power profiler kit. I wanted to tested current consumption at different...
Hi Nordic Community,
I am trying to build a network using the OpenThread protocol and the nRF52840 chip. I have several Dongles, but I can't figure out how to flash the...
I'm importing ble_app_blinky_pca10040_s132 example in segger IDE. I'm using EVK-NINA-B1 and from nRF SDK I'm trying to importing example but getting error as mentioned in...
I have an external clock running at 3Mhz which I'd like to align with in software. Consider this contrived example:
What would the consequences be of attempting to read...
Hi,
I'm very new to c programming and your hardware. Please excuse my novice questions.
I'm making a rotary braille display using nRF52840 dongle (PCA10059) as it's brain...
Hi,
I using custom nrf52840 board .I have loaded the Bluetooth program in to the custom board using swdio/swclk/vtg/gnddetect these lines.There is no problem in Bluetooth...
I'm attempting to get MMD set up in an IAR project following this tutorial: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/monitor-mode-debugging---revolutionize...
Dear sir, We are using BL654PA from Laird technologies. We want to check RSSI at 2402MHz, 2440Mhz, 2480Mhz. Can you guide us how to enable PA without using Nordic stack file...
Hello,
I'm using a Thread Border Router built using a Raspberry Pi 3 and a nRF52840 Dongle. I followed the steps at this link: https://infocenter.nordicsemi.com/index.jsp...
