2025-06-13T08:43:42.649Z INFO Initialising the bundled nrfutil device 2025-06-13T08:43:42.652Z DEBUG Started watching devices 2025-06-13T08:43:44.400Z INFO Using the bundled...
I am using two nRF5340 Audio DKs one as a gateway and the other as a headset. I tested the nrf5340_audio example and managed to get the speaker output working through the...
Hello, Has anyone implemented Deep sleep in nrf52833, v2.9.0?
What all I tried :
1. tired to use "pm_state_force(0u,&(struct pm_state_info){PM_STATE_SUSPEND_TO_IDLE, 0...
Hello, I am trying to use the DPS368XTSA1 sensor with the nRF52833 via SPI. First, I’m attempting to read the sensor’s ID during initialization, but it’s not being read properly...
I want to implement deep sleep (wake up using RTC at a particular time interval), and determine the current consumption in nrf52833 dk. So I used the sample code first. When...
I’ve designed and fabricated two custom boards around the nRF52840 SoC.
I use an nRF52840 DK as an SWD debugger to communicate with each board.
Using nrfjprog...
Hi,
I have a custom board for the nRF54L15. I have already implemented LEDs and a button, which work fine. But I cannot get the PWM peripheral working, and I do not understand...
hello:
our hardware engineer had designed PCB,it can't reach more than 100m..howerer the nrf52840 DK can reach 300 or more meter.
so is there any people can support some...
When using nrfutil to generate a DFU settings page (with backup page) of settings version 2, the .hex-file generated by nrfutil is not word-aligned, i.e. the number of bytes...
I noticed that as of SDK v16 a required component to use the Soft Device is nrf_section_iter which is located in the directory "\libraries\experimental_section_vars". Is this...
Hello,
The product specification for the nRF52832 only shows 3.0V performance. What is the performance in parameters such as Tx power, Rx sensitivity, maximum MCU clocking...
Hi,
I'm currently developing firmware in the Arduino environment using a dev board (Adafruit Feather nRF52840). Once I complete development, how do I transition the firmware...
Hi, I am developing the application in nRF52832 with SDK_16 in SES.
I have a problem with DFU
I need to run the application and DFU has to be activate only if the mobile...
Hello everyone
I'm using NRF MESH4.0, I have add simple_on_off model to experimental_dimming example,and it works .
My question is : MESH PROFILE V1.0 have mentioned bound...
Hello, i am trying to adapt DFU in the Light switch Proxy server example, however in midle the process of receive the DFU packets i got this error: Abort event. packet loss...
Has anyone (tried to) simultaneously use the same QSPI Flash memory directly from an nRF52840 program and as a USB block device?
We have both functions running in the same...
Hi
I am working with nRF52832 DK, using Segger IDE. I want to read data(a file) from a computer and process the data on DK. Is there any way of doing it? Also, is it possible...
Hi Nordic Team:
Can you help me to support BIS or CIS example .btt file。This file was captured by Ellisys tool。So ,I can refer to file ，and understand 5.2 Core Spec about...
Referencing the recommended 52840 PCB layout for the WLCSP package, we noticed two thru-hole vias in the middle of the ground area (in the center of the package). Do these...
Hello,
I am trying to implement ble DFU on our custom nRF52832 board. Up until now we have had no issues with our application running as SoftDevice+Application but some...
I'm attempting to send a time sync message in a mesh packet. When I construct the packet during it's timeslot (for timing determinism) the system faults during encryption...
