Hi Nordic team,
We are planning to use the STM32H747 as the host MCU to control the nRF7002 for Wi-Fi functionality. Based on reference materials and existing use cases...
Hello Nordic team,
I am working with the nRF54H20 and would like to integrate both Enhanced ShockBurst (ESB PTX) and Bluetooth Low Energy (BLE peripheral) protocols in my...
Hello, I'm testing the nRF21540 FEM on a custom nRF52840-based board using the nRF Connect SDK.
I’ve enabled CONFIG_MPSL_FEM CONFIG_MPSL_FEM_NRF21540_GPIO_SPI CONFIG_BT_LL_SOFTDEVICE...
Hello, checking if I'm doing this right of restoring initial fw for 91X to work with Quick Start v1.2.0. as described here in Get Started, https://www.nordicsemi.com/Products...
It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I can't figure out why but my build cannot locate files that are included in the makefile.common
I'm using SDK 5.1.0 and the ble_app_hrs project. It seems it can't find one...
My device is smart watch. We transfer some data to phone and receive notification from phone over BLE.
My question is those two functions(connect_params_init and sec_params_init...
Hello
I'm new in the world of nordic semiconductor and I've a little problem. I would like to transfer ANT+ data of a HRM Garmin in serial protocol to my PC. I use a nRF51422...
Hi,
I transmit a data packet to AP2, i wonder if it needs a sequence for resetting or not while AP2
initializing.
And, I send a packet data to AP2 by UART(AP2...
Hi Folks,
I'm experiencing a problem with the nRF8001 setup. After I send the last setup packet, I still receive:
0x03 (length), 0x84(CommandResponseEvent), 0x06(Setup...
I'm getting this error, but oddly it's coming up somewhere in the MIDDLE of my build, and not always the same point.
I have modified the HEAP size to be 0 as I don't do...
Hello !
I have just received the Evaluation Kit nRF51822-EK. I succeed to compile link and load the blinking leds example from my Linux box. I modify the example to use...
So, how do I control where my app is going when gdb pushes it to the device?
I'm using s110 6.0.0, no boot loader. How do I make sure my app is going to where the SD will...
Hello,
I'm trying to make use of the AES crypt code from the application level code.
Per devzone.nordicsemi.com/.../51822-aes-encryption-and-decryption-demo-code
...
I am planning to record some information in the flash of the nRF51822. This will occupy a large circular buffer (quite a few kb), and new data (in chunks of around a dozen...
hi,
i survey the Bluetooth again , i have some issue about the Connectable mode
Connectable mode.
i see the peripheral connectable setting :
PERIPHERAL :
...
Hi Nordic,
How many connections was S120(Central) can handle simultaneously?
Does S120(Central) can received the notifications from different peripherals...
Dear all
I notice that Gzaell could only send 32 bytes a packet. But I check register PCNF1 MAXLEN can be set over than 32 bytes.
Is there any way to increase overall...
Hello,
Is there a way to set the OOB key while using the master control panel windows software?
Edit: and if not, is there a quick method to test a peripheral's OOB...