after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello,
I have a few questions about the nRF9151 DECT NR+ modem.
I see that from the docs that the max TX power is 19dBm, so it's a Class III device as defined in section...
zephyr\subsys\bluetooth\mesh
zephyr\subsys\bluetooth\mesh\shell
I need to use APIs for certain files in the path mentioned above. Currently, I can only copy the files...
Hello,
I am experiencing an issue while trying to connect an external flash memory (MX25R64) via the QSPI interface on an nRF52840-based custom board. My pin configuration...
Hello.
I tested the DFU distributor sample using two nRF54L15DKs. I have three questions.
1. Apply is not completing. The firmware transfer seems to have completed, but...
hi support tean,
customer is asking about " Credential storage management %CMNG" in our modem, how to calculate the hash value
i have put the log in below:
[12:33:32...
Hi Sir ,
I am running the nrf/samples/bluetooth/direction_findinding_connectionless_rx App on an nRF52833-DK with nrf Connect SDK 2.7.0 and toolchains v1.6.0 version.
...
Has anyone experienced the following error when Flashing (and debugging) from within VS Code. I have no idea what has happened, but it has hit several projects.
Even though...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Hello,
I am modifying an existing custom board with a sensor that requires exactly 1.9V VDD. Previously I was configuring REGOUT0 = UICR_REGOUT0_VOUT_2V1 but I was surprised...
Hello, I want to implement a project with BLE mesh. Several nRF52480 boards should form a mesh and e.g. send the status of one of their buttons to a tablet. What would be...
I hope this message finds you well.
I am currently working on a project using the nRF9151-DK Evaluation Board and have been testing GNSS functionality in various environments...
Hi there,
We have an Icarus IoT board, which uses an nRF9160 SiP. I am trying to get the nRF Cloud Multi Service sample to work. I am getting the following errors:
mqtt_connect...
Hi there. We have recently migrated from SDK 2.6 to SDK 3.0.
We have a custom-made external board, which we used to program with the nRF52840 DK when using SDK 2.6 (for...
I'm encountering a blocking issue when trying to create a new board using the NCS Board Wizard in VS Code with Nordic Connect SDK v3.0.0. After filling in valid inputs and...
Uploading via VSCode since version 3.0.0 (happened with the rc1 as well, Toolchain 3.0.0 and Toolchain 3.0.1) does not work for the nRF54L15DK (board rev 0.9.1 ENGB chip)...
