I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
I want to use spio of nrf52811 soc using nrf connect sdk 2.7.0 version with vs code.
I am trying to get spi devicetree specifications using
struct spi_dt_spec spispec...
I was wondering how I can update my current code (see below) to reuse a single socket for multiple HTTPS requests, rather than opening and closing a socket for each HTTPS...
I have v3.0.0 SDK currently . I am using nrf54L15DK . Do we have any sample code for checking AOA and AOD of the advertisements from the peripheral devices.
I could find...
Hello Nordic team,
I would like to automatically patch the merged.hex file each time I build my project. I’ve attempted to use extra_post_build in CMakeLists.txt , but my...
Hi Nordic
I’m working with the nRF5340 and nRF21540 for 802.15.4 and would like to know:
The expected RX sensitivity estimation for this combination.
Any reference...
Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hi
I've recently tried to move from SDK version 2.6.3 to 2.9.1. However i've run into issues with this transistion.
I made a new custom board, by following the guide...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
Hi Nordic Team
We are developing products using the NORDIC NRF54L series chips, but we are encountering some hardware issues.
We have used the NRF52832-QFAA chip. Packaged...
1st issue: Tingy91X doesnt build at all with debug -Og enabled: Because of all the strange issues of Thingy91 (nRF9151) and "not to be used in new products) we ordered a couple...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
this is my prj conf
# Bluetooth
CONFIG_BT =y
CONFIG_BT_BROADCASTER =y
CONFIG_BT_OBSERVER =n
CONFIG_BT_PERIPHERAL =y
CONFIG_BT_DEVICE_NAME = "Range extender"...
