Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
I just want timer2 to run at 1Mhz so I can grab a microsecond counter as a timestamp. I don't care that it'll overflow after 32 bits. Put together what I thought should be...
Hello, I'm using the Radio Test software (SDK 15.2) to control the N52840 radio IC. Our circuit design requires the use of an external RF amplifier IC. Our software puts the...
Hi everyone,
I am stuck with an apparently simple problem which I am not able to fix.....
I have an SPI device connected to a custom NRF52840 board. I am using NRFX_SPIM...
As per the section - "Adding support for programming nRF5340 in SES" in the document https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf5340.html , I had...
Can you please guide me how to compile the nRF Connect SDK asset tracker with the AT command library enabled. I need to set the CONFIG_AT_CMD_RESPONSE_MAX_LEN configuration...
I tried to connect my nrF52 DK board to various devices, via USB. None of the devices was able to see the board.
In addition, nrF Connect / Studio wouldn't see the board...
Hello,
I am trying to understand how to use an external button. In the first stage I am trying to replace the functionality of button0 on the DK with a GPIO.
I took the...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I'm working with the ble_peripheral example...
Hi, We are using the nRF52840 in a 3V battery powered product. We have an on board 1.8V LDO regulator that supplies Vdd and Vdd_IO. We have a problem with the NFC antenna...
Dear all
I currently have a single nRF52832 SoC (custom PCB) transferring data to a single nRF51 dongle via BLE, which in turn passes the data to my PC via UART. I have...
Hi everybody,
I'm having a problem with the advertising function of the SoftDevice.
When the application starts advertising the function "sd_ble_gap_adv_start()" returns...
Hello,
We are currently looking for a way to test nRF52804 on our board with CMW500. From R&W video clip, they tested Nordic eval. board with USB connection. How do I make...
I’m interesting particularly nRF52832 and nRF52840 (with and without bootloader)
So looking at flash layout with bootloader :
is the section ‘Application data’ available...
i want to send string over eddystone tlm...and wish to use temperature part for this...so how can i display character string instead of temperature in eddystone TLM..please...
