Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,
I am testing the ble_app_hrs project on two eval boards, with s110 and s120. Everything works.
If I power-off the peripheral board (s110), it seems that the master...
Dear Nordic guy, I'm developing with nrf51822.
I have one question regarding flash write.
In ble connected state,I have some error to write some data to flash.
I want to...
Hi,
I just loaded the nRF8001 Arduino code on my board and used an iPhone 5 to read the data that was being advertised. I get the following response:
<CBCentralManager...
Dear Nordic guy,I'm developing with nrf51822.
I have one question regarding lfclk.
I use LFCLK SOURCE RC OSCILATOR of ble_stack_handler_init() at the application side.
...
Hi,
Is there any example application related to alert notification profile for android 4.3 devices?
I just need to understand the gattserver implementation for the alert...
Hello All,
Since yesterday I have been getting a problem where my project using the S110 softdevice enters a reset loop. This runs on a unmodified PCA10001 that plugs into...
Hi,
I need to design a board that connects various sensor to a smartphone using the Bluetooth 4.0.
I'm interested in the NRF51822 chip but i have some doubt about what is...
Hi, I'm very new to programming microcontroller, so please go easy on me. :(
Firstly, apology if my post sounded weird, this is because English is not my first language...
Hi all.
I am making a custom PCB with nRF51822 SoC. For my project I need to achieve long Proximity range around 350 Feet. Where my Board will communicate with iPhone....
I have a timer that sends BLE data to a central every 5 seconds. The timers starts immediately out of reset. Until I actually pair the devices, the nRF51822 outputs an error...
I have problem to debug when I use softdevice it frezzes. At the moment I debug the program part with out use of softdevice is there any other solution? It the same code with...
Hi all.
I am new in nRF BLE. I am planning to buy an nRF51822 Kit but little bit confused with choosing EK or DK. Actually my plan is after playing with the Native Kits...
I am currently designing a board using the nRF51822 chip and I would like to implement a soft power ON circuit using the low power comparator (LPCOMP).
I understand that...
Hello,
I'm using a code posted on this forum to read ADC input and fill an array with the ADC values but I always get values between 166 and 174, (even if I connect the ADC...
