Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I'm trying to use MBEDTLS with MBEDTLS_USE_PSA_CRYPTO and CONFIG_PSA_CRYPTO_DRIVER_CC3XX activated.
Unfortunately I can't find a way to tell MBEDTLS that nRF9151...
Hi,
I have designed a custom board, and I cannot get coexistence interface to work reliably. I don't get any errors, but I'm not able to connect to my board with BLE. WiFi...
After an update recently with the nRF Connect for VSCode Extension, it's been unable to find where my nRF Connect SDK is located when choosing a build configuration. It used...
Hi, would like to understand what scenarios a clock stability better than +/-40ppm would be needed in a BLE setup.
i.e. channel sounding, and similar. I mean you can get...
1st problem:
There are some failed case when i run \v2.9.1\modules\bsim_hw_models\nrf_hw_models\tests\zephyr_apps\54_aar_ccm_ecb\src\test_ccm.c
2nd problem:
If I...
Hello,
I plan to use uart1 for serial port development based on the binary protocol. I will receive bytes using the interrupt method. But when I send bytes (such as FAFBFC...
I have a custom board with nrf5340 and want to run the radio_test sample on it. I have been able to compile and run the sample using the uart serial terminal, but I'm not...
Hello,
our project which started 7 years ago with SDK13.0 has been migrated some time ago to SDK 15.3 and now to SDK17.1. At the beginning we were quite happy with the RTT...
Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
This happens quite often, I simply has to create a new build configuration and in worse cases simply a new application and copy all my sourcefiles over to the new project...
Hello everyone.
i want to configure the TX power of the NRF radio in BLE advertisement and connection of the NRF54L15 MCU. I am using the nrf Connect SDK version 2.7.0....
I am studying Lesson 6/wifi fund_1ess6uexer2 and I can run the provided code normally.
（academy.nordicsemi.com/.../） But I still want to control whether to send packets...
Hi,
I'd like to go for sysbuild with my nrf9161 based application but after some trials and errors, I am not able to find which images should be enabled in sysbuild.conf...
Problem - while working in a project where VSCode does not have visibility to the nRFConnect SDK folders, but where the project includes project-specific KConfig files, the...
Hi, I have cloned the channel sounding with range requestor samples but every time I try to build it I encounter the error:
I have not changed the code or anything, but...
