Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi Guys,
Is there a way with the Keil C Compiler to get an *.LST file or some sort of Assembly output from C source input?
I'm still trying to write some code to drive...
Hi
Now, I am coding SDK5.0.0 keyboard project and almost done. It's Keil C version. Did you have IAR version for reference? Besides, did you know if IAR supports J-Link lite...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
I would like to know how to implement reset button on nRF51822. Image of schematic would be very useful, but good explanation should be enough. Thank you in advance.
I...
Hello,
I am trying to build the nrf51822/Board/pca10001/s110/ble_app_proximity project, with gcc ...
I have created a makefile based on the button_radio_example makefile...
I would like to know if the Notification/Indication of a Characteristic is enabled. I suppose this data is stored in a CCCD on the stack. I have not found any SVC instruction...
It seems the only way to use the S310 alpha hex on the development kit is to replace the IC on either of these boards; is this correct or is there another way?
Also, the...
Hi,
I am researching BLE product for a similar task (1 central node with 4-6 concurrent slaves). I have looked up other vendors (TI, CSR etc) and come to a conclusion...
After Googling and searching this forum I still don't know if I can make an HID peripheral (a touchpad) for Android that operates over Bluetooth Low Energy, and is accepted...
Over the air downloaded updates are an essential feature for productization. Are there any examples showing how to implement the OAD? Also is it possible to OAD update the...
Hi,
My nRF51822 evaluation board is not working, here i attached the screen shot's of the error messages i used to get on both the nrfgo studio and in keil. Please suggest...
Hi
When I reduce the operating voltage, the nRF51822 with the heart rate demo running resets whenever the voltage drops below 2.1V and does not recover unless I increase...
I need an star network with 1 master and 4 to 8 slaves. I'm not so concerned about the power, but the convenience of the nRF51822 is attractive.
Does the current BLE library...
Dear all:
Now,i have issue ,i can't fund device.(i have sure the hardware is OK)
i think it is program overwrite the J-TAG register(TDO)? but i may not sure.
have any experience...
The Arduino SDK by David Edwin linked to here is no longer available since the Bluetooth forum seems to be down, and has been for some time: devzone.nordicsemi.com/arduino...
