Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
hi everyone
After using Android nRF Connect FOTA, the settings storage partition of my device was erased, which means that my device's PAIR information was lost and the...
Hi Nordic Team,
I'm looking to use the UICR->OTP region ( One Time Programmable (OTP) memory region within the User Information Configuration Registers (UICR)) on the nRF54H20...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Hi Nordic Support Team,
I'm currently experimenting with Channel Sounding using a couple of nRF54L15 boards.
I am trying to obtain raw I and Q samples so that I may analyze...
Hello,
currently i am configuring the networking stack on my project.
The goal is to use Matter's built-in Thread connection, to establish a Secure CoAP connection. I...
Hi,
I am desperate with creating my own board. I followed the example of nrf54l15dk, but I absolutely do not understand why I cannot build - not even assembling Zephyr....
Hello,
I am working on custom hardware that is based on the nRF7002 DK. The following parts are presently listed as either EOL or NRND in distribution. L6, L8: Taiyo Yuden...
I am trying to connect some I2C sensors to the the nrf9151dk and I cannot figure it out. Where do I physically plug the sensor into the board and what configuration setting...
Hello,
Hopefully this will be a quick(ish) one since I think I found the answer, but just need confirmation.
To preface (My setup):
nRF9151DK
Modem firmware: mfw_nrf91x1_2...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hello,
I am having some trouble with the UART API (Async and interrupt). I am connecting the development board (nrf9151 DK) to a 3rd party device (keypad / prox reader)...
Hello! One of our projects will have nRF52832 replaced in EMS with revision 3 silicone and we wonder if description in is valid. It states that:
In factory state, the [new...
Dear Nordic-Support,
I have registered handlers for the two voltage level thresholds with the nrf modem library using modem_battery_low_level_handler_set and modem_battery_pofwarn_handler_set...
Nordic #Devacademy intermediate course: Ticket for exercise 2 of lesson 2
Dear Colleagues,
I selected the #nRF9151-DK, since it was in the list of recommended boards for...
Hi Nordic Team,
I am working on implementing synchronized sensor sampling on multiple Bluetooth devices that are externally triggered. To achieve this, I have combined the...
Setup: NCS v2.8.0 nRF52840
Hi,
I would like to ask about the implementation of Zephyr's SAADC driver (` adc_nrfx_saadc.c `).
In the project I'm working on, I need to...
Hello, my application requires very precise timing to trigger an action on the edge of the GPS time. I just need to get this time once in a while to synchronize the system...
Hi,
I am currently working on a two way communication between an nrf52840 thread host and an nrf52840 thread client over coap. I have nrf connect sdk version 2.9.0 in both...
I have recently bought two nrf52840dk, version 3.0.0, unboxed and plugged into usb. One would show up with a usb storage on the side and in vscode a J-link window prompted...
Hi,
I am getting framing error notifications from the nrfx uarte driver on a zephyr platform when receiving data from a certain external device, but only when there are...
