We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi
The bug can be found by following the below steps.
Pair nRFready keyboard (Desktop 2 v1.0.5) to Windows 8 BTLE host. The keyboard can work.
Disable Windows...
Hi ,
Here is my code used to write in to non volatile memory.
#include "nrf.h"
#include <stdint.h>
#include <stdbool.h>
#include "nrf_nvmc.h"
static void flash_page_erase...
Hi all,
I can see the DFU project in SDK and know that the device firmware can be updated by using BLE and UART.We just use the 2.4G to do the airplane model.But I donn...
Hi ,
Here is my code used to write in to non volatile memory.
#include "nrf.h"
//#include "uicr_config.h"
#include <stdint.h>
#include <stdbool.h>
#include "nrf_nvmc...
hi,
i want to get the Email,MissedCall,Other(SMS) from Apple(ios7) to my device.
i survey that , ANCS(Apple Notification Center Service ) at the the Latest iOS7
and access...
Hi
I'm using the nrf51822 with Softdevice S110. I want to find out why a pairing has not worked, PIN-Code was wrong, PIN-Code timeout.
Which events I can use for that...
Hello,
I have tried the nRF51822 SDK example , "ble_app_hids_keyboard", it can send text "hello" to iPhone. When I cut off the power of the nRF51822 and turn it on again...
I have nRF8001-DK and Arduino Uno. ble_uart_project_template from nRF8001 SDK for Arduino (Bluetooth_low_energy_for_Arduino_0_5_0_0_RC2) was used. It was used with Master...
Hello,
i create a custom profile with two services and with 30 characteristics. The first service has 29 characteristics. Up to this point everything is ok, but when I...
Hello, i would like to know if its possible to use your SDK tools (S110 Soft Device, nRF51 SDK) without your evaluation/development kit.
Since RFduino has a RF51822 chip...
Hi, I try to create a iBeacon tag with NRF51822 for Apple device, but it seems not to work, yesterday I update the newest SDK, I found the ANCS was added, so Nordic also can...
Hi,
i have a big Problem, if i debug my code i get in some cases in register 3 the value 0xDEADBEEF and after that the device doesn't work any longer in a correct way....
Hi
I can use the duf_dual_bank_ble to do the OTA,but I donn't know how to use the dfu_single_bank_hci to do the OTA.Could you give me some
advice about it?Thanks.
Hi.
I have a problem with writing value to gatts attribute when device is in connection mode. In my application I want to check if the parameter writing by the client to...
Hi,
I have downloaded the new version of SDK (v.5.0) today and just tried your experimental ble_app_ancs (no modifications) but it seems it asserts with error_code=0xB...
