I think this code snippet is causing the issue, since I am able to make the device work by setting:
' NRF_SDH_BLE_PERIPHERAL_LINK_COUNT = 1' and 'NRF_SDH_BLE_TOTAL_LINK_COUNT...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
I ran into this last night and curiously, James appears to have posted about it yesterday ( devzone.nordicsemi.com/.../trouble-with-system-halted,but-cannot-reset-nrf51822...
I am trying to get the Heart Rate example in the nRF51 SDK to work (found in ...nrf51822/board/nrf6310/ble/ble_app_hrs). It fails at line 338 in main.c (at the call sd_ble_gap_device_name_set...
I'm putting some bootloader and static config data in the customer section of the UICR and I accidentally wrote to 0x1001200 and worked just fine.
Looking closer, it seems...
Dears:
We will adopt nRF51822 for our project, and we want to confirm with you for the question as below:
Does nRF51822 support HCI command protocol through either...
Hello,
I do erase flash pages in my application I use the sdk api:
nrf_nvmc_page_erase(firstaddress);
nrf_nvmc_write_bytes(address, data, len);
but I did not found...
Hello,
i couldnt find the correct answer yet. I would like to use a RTC and also the s110 and BLE.
I collect data from sensors over i2c and send it over BLE. timing...
My username and password credentials do not work here or on the normal nordic semi site. The random password (i.e. fj[k%3) will work at the nordic semi site, and continue...
Hi,
I am starting development on my project using the ble_app_hrs as a template. This project already has the buttons setup for interrupts using the Button Handler library...
Hi guys
I use gazell protocol for my application. I want to try some other way to decide the channel tables. So I decided to monitor the RSSI and chose the channels in...
Hello, I want to be able to perform actions in my app based on the tactile buttons being pressed on the beacon. When I bought it I was under the impression that the service...
Hi,
I have some problems to advertise a custom 128bit UUID.
I succeeded to set the 128bit base UUID and my Characteristics UUIDs are 128bits.
But how I can set the PrimaryService...
Hello,
I want to implement device pairing, using the pairing bit. The pairing bit is set in the masters device type. For a slave to pair with such master, it opens a channel...
Hi Nordic!
I am using nRF UART2.0 and nRF51822.
I am sending some data from nRF51822 to nRF UART2.0
But after 3 minutes, I can get disconnection.
and 0x16 error...
