Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
My ble device try to notify a data to my android mobilephone after phone connect it,but sometimes,phone can't receive the data and error 8 occur .this happend frequently when...
Hi,
pstorage_raw_store() API fails as p_src address is not 4 byte aligned (i.e. 0x20002b1a), as p_src is RAM address and also as its "SOURCE" address is it necessary to...
Hey Folks
I wonder to design my own simple circuit based on NRF51422, the circuit should connect to a mobile app. By the way I'm I wonder to follow these steps:
visulaised...
Hi all,
I have one question about the deep sleep wakeup process in NRF24LE1. I want to realize the function that "when I press the button, it will cause rise edge on the...
Hi,
I'm testing doing a soft device update (v7.0 to v7.1) over DFU, but I consistently get OP_CODE_SYS_RESET sent to my device after 4 packets(80 bytes), at which point the...
Just want to know how acknowledged message works.
ANT document says there is no retry logic for acknowledged message.
According to ANT protocol, acknowledged message should...
Hi all!
I've been trying to OTA firmware using iOS nRF Toolbox App. I'm able to read.hex files in the App, although, after trying to send the file to the device the format...
I have a "heartbeat" LED which flashes for 10mS every 2 seconds. I was doing this with one of the HW timers and a PPI channel, but I have discovered that just having the HW...
How would I go about changing the connection event packet length?
I have an 8 byte characteristic setup with notifications enabled, but it still looks like it is transmitting...
Hi,
I have the following code with SD110 7.1.0:
static void uart_init(void) // device inter-communication
{
// Configure RX and TX pins.
nrf_gpio_pin_set(0);
nrf_gpio_cfg_output...
Hello,
I am building a sample protocol using nRF51822 DK. I am using S130 soft device. I have a few BLE nodes communicating with each other. The nRF51 DK acts as these nodes...
Is the nRF51822 pin-for-pin compatible with nRF51422?
I can't find any distributor stock of nRF51822-QFAC.
I see the eval kit has nRF51422. I don't need ANT functionality;...
Hii, i use nordic PCA10028 dev kit, to test the bluetooth of kit i simply load the ble_app_hrs example which is given in SDK, because of i don't know how softdevice 110 is...
I'm currently designing a system that requires Nonvolatile memory. Whilst I can accept the 43uS delay to write a word to flash memory. My concern is that it is entirely possible...
