I try to get the one button sample to work. There were several details missing to be able to compile and run this sample, which was very frustrating. After editing/updating...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
Hi there,
I am trying to implement some power saving features of my device, and am having trouble with stopping advertising in SDK v3.1.0
I would like to advertise for...
Hi, I have an Adafruit nRF52840 Feather Express and am developing for it using Zephyr 3.1.1 and the nRF Connect SDK with VS Code.
I want to read and write from two of the...
Hello, Nordic Team,
I am writing to request assistance with a Mater commissioning issue we are facing. We are in the process of preparing out product for Matter certification...
I have a Zephyr application running on a NRF9160 using the Golioth SDK. I updated from their SDK from v17 to v18 and started getting undefined reference linker errors. I’ve...
Hi guys,
I have made a custom PCB based on the nRF5340 and for debugging it I have only added a SWD interface.
The problem is that this PCB works with 1V8, and in the...
Hey folks, I've tried bunch of things but can't make TWIM work properly on nrf54l15-DK outside of that pair of pins. Basically the issue is that it only works correctly if...
Hello all,
I’m working with the nRF54L15DK development kit and I’m facing a debugger / flashing issue. Below are the details:
Setup / hardware used: nRF54L15DK
On-board...
I'm using the nRF-PPK2 in ampere mode to measure power utilization in a battery powered device over a long period of time (about 16 hours). However, the PPK2 is giving unreliable...
Hello Nordic,
I am developing for a project that requires real-time accuracy. We are using ncs v2.9.1 Zephyr, an nRF54L15 and an IMU (w/ SPI interface) to acquire positional...
Greetings,
I would like to enable triggered firmware update option (dfu icon to be shown and to work) in NRF Connect android app on button press or uart. I followed the...
Hi,
I followed the instructions for enabling mcuboot and OTA using DFU target APIs using the instructions here -> https://academy.nordicsemi.com/courses/nrf-connect-sdk...
Dear all
I am developing a product using the nRF54L10 with the Zigbee add-on v1.2.0. I have a question regarding sleep behavior.
The current measurements below show the...
Hi,
I am developing an application with the latest available version of the nRF Connect SDK (v3.1.1) for the nRF54L15 SoC.
I want to develop an application with B0 + MCUboot...
the existing code is using freetos, and main.c finally ends at
which never returns as expected... but my ble scan and advertise do not appear to work, no events...
Hi,
I'm working on a four layer PCB including the nRF7002 for WiFi location finding. After looking at the various Altium Design files available (Thingy91X, nRF7002Dk, nRF7002EK...
