We are developing a new board based on the NRF9151 and would appreciate some guidance regarding the power supply design for the modem.
Specifically, we’re looking for documentation...
What is the default transmit power of the nrf5340 when performing an AoA test in connected mode? How do I change its transmit power to perform AoA accuracy tests at different...
I'm trying to build the light-switch-app from Matter but I get following errors
I have already tried to reinstall the sdk (I use v2.8.0) and build it just like that without...
Hi all,
We've followed the reference EVK designs closely and are now in the Pre-Production phase.
The initial development board was intentionally large to accommodate...
use "nrf5340 cpuapp" to compile project, flash statistics as follows, see blue color
[3/11] Linking C executable zephyr\zephyr_pre0.elf
[6/11] Linking C executable zephyr...
Hello,
I want to set my TTL value in a node (nrf52840 dongle) that i use as a relay node.
In prj.conf file I set the node in this way:
CONFIG_BT_MESH_RELAY=y
CONFIG_BT_MESH_RELAY_RETRANSMIT_COUNT...
Hi,
I am running Matter TH.
Among them, there is an error in the TC-DA-1.2 test step 6.9 certification_type check.
The reason for the error is that the certification_type...
Hi,
We are facing a critical power consumption issue in our nRF52-based Zephyr application , where some devices randomly enter a high-power consumption state (~80+ µA) instead...
Dear Nordic Team!
We are struggling with a fatal error occurring during boot phase before entering the application main. When setting the baud rate of UART2 to 38400 or...
Hi,
Two month ago I have test nRF21540 and nRF54L15, they cannot word with each other.
However, I notice these days updated with
https://docs.nordicsemi.com/bundle...
Hello,
I am trying to use the nRF21540 in nRF54L15, I notice document metion
I am wondering what is the difference between PPIB and DPPIC. What does appropriate...
hello, I encountered a problem using SPIS to communicate on nrf54l15
Environment: NRF54L15, NCS2.8.0
When using SPIS for SPI communication, you must first write empty...
We are using nRF Connect SDK 2.9.1, Zephyr. The hardware used is a nrf52840dk, rev2.
We have a proprietary protocol that is running concurrently with BLE and uses MPSL API...
Hi everyone
I am using the nRF9160 DK board with the VS nRF Connect extension. I am stuck at lesson 7 exercise 1 of the Cellular IoT Fundamentals lesson.
Up to this lesson...
hi support team,
i want running chat demo in mesh fold in ncs2.9.0, but it doesn't support thingy53 natively. so i ported some of the file from light to chat demo. you can...
Hi everybody,
I'm writing because I'd like to check if I understand the functionality of the AT command AT%XBANDLOCK correctly.
The first part of the question should...
Hi! I have been developing a GATTClient and GATTServer on two separate nrf52840dk boards and have been doing so for a long time.
This Friday I got everything to work when...
Hi Nordic Team,
I'm currently working on a BLE project using NCS v2.9 and targeting a custom board based on the nRF54L15. My goal is to use the SYNTH LFCLK source (instead...
Hi Nordic Team,
I'm facing an issue with BLE communication on my custom board using NCS v2.9. I started from one of the standard SDK examples (like throughput or peripheral...
Hi,
I just got a PPK2, I'm going to measure the current of a nrf52 custom board, which is supply with Li-ion battery.
Should I connect GND on PPK2 to battery(-) when I...
