An external MCU occasionally sends data to the nRF54L05 over I2C. Between transfers, the nRF54L05 should sleep and wake when addressed, without a separate wake pin.
What...
On a custom Zigbee End Device application for the Thingy:53 (NCS v2.9.3), ZCL Configure Reporting commands sent by Zigbee2MQTT are rejected with ZCL status FAILURE for almost...
Thanks in advanced. I'm immigrating projects into NCS bare metal v2.0.1. Sample Bluetooth ble_nus only advertises for 3 minutes, then device can't be scanned again. I check...
Hello,
I'm following online courses in Nordic Academy (nRF Connect SDK Intermediate).
As indicated in the first lesson,first excercice, I added device_message_queue...
nRF54LM20 + nRF7002, NCS 3.4.1: SoftAP provisioning and station low power in one image
Our battery-powered product (no BLE antenna), removed due to space in the PCB and...
Hi
Have you done any benchmarking to estimate the difference in power consumption when comparing the nRF9151 in NTN mode vs LTE-M?
In particular I am curious if NTN has...
software: ncs v1.8.0
hardware: my test nrf52833 board, with 9 antennas.
I do experiment like this:
aoa rx: in "nrf52833dk_nrf52833.overlay" file, I set " dfe-antenna...
Hello,
I am trying UDP sample with a local SIM (Orange) to check eDRX settings following this ticket .
Carrier said i should set an APN. This was not needed with 1NCE...
I try the new save to CSV feature in v3.4 power profiler.
I try to save all, but it says 0MB.
The sample rate is 100ksps, and duration is 301 seconds, but would result...
Hi, I have the following code in main.c:
If I initialize the beacon advertising first, which is the shown configuration, I get fatal error code 8 out of ble_advertising_start...
I have recently updated the SDK for my application from version 13.0.0 to 17.1.0, everything seems to be in order except for this function in nrf_drv_twi.c called twi_clear_bus...
the updated version of nRF connect v3.8 , for desktop , app - programmer doesnt recognize the device . i downgraded to 3.3v this version selects my device .
Hello,
I have developed a Thread network based on SDK for Thread & Zigbee v.4.1.0 and OTBR image provided by Nordic. I recently upgraded my OTBR from a Raspberry Pi 3B+...
Hi, I have added libuarte example in-app template and sent data from Arduino to nRF52840 successfully. But after receiving some data and I am getting the following error....
Hi,
I use nrf5340 and have issue with i2c large buffer send: In order to flash page to bootloader with my application:
I defined
I defined static array with size...
Hello !
If I understand right and nrf_crypto is the main Crypto API in nRF SDK. They can be mapped to cc310 or to mbedtls sw routines.
Does exists nrf_crypto asynchronous...
Hi,
When I try to run a colleague's project on my PC in debug mode in Visual Studio Code, I get the error "Run to 'main' timed out. Trying to pause program":
The debug...
Hello, guys.
We have nRF51822 SoC with 256KB of Flash and 32KB of RAM memories at our disposal. For our application, we would need to use the BLE stack + over-the-air DFU...
Hello! I recently dived into using the nRF52840 SDK + Zephyr the goal is to use this for Bluetooth Long Range Extended Advertising. Are there available tutorials, resources...
Hello,
I am using sdk12,2.2 and nrf52832. I have interfaced bme680 sensor with nrf52. I am facing strange challenge.
My button interrupt is working every time but it stops...
