I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
Hello Nordic team,
I am testing a plain CoAP telemetry upload from an nRF54L15 DK over Thread using a Raspberry Pi OTBR and NAT64 to ThingsBoard Cloud.
Hardware / software...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
Hi,
Would you please explain the default behavior of peer manager Garbage collection when buffer is full if I don't call Garbage Collection?
I have tested with small number...
When implementing Shell NUS option we've faced with the following: NUS transport takes in account only 'enter' symbols and doesn't react to ones like up-arrow, down-arrow...
The interface "sd_ble_gap_adv_start" uses "adv" to indicate broadcast, but the interface "ble_advertising_start" uses "advertising" to indicate broadcast. Why not use the...
Hello Nordic Team,
I am trying to flash the existing BLE light example code to my BL653 kit with Segger Embedded Studio. After falshing the code into the board it is taking...
Been having trouble integrating systemview for tracing FreeRTOS application. I came across this thread , and even tried replacing the files with what's inside the PatchedFiles...
Nrf Mesh App Version 3.1.6
After provisioning 2 nodes, I connect to one as a proxy, whenever I try to "get TTL", "Read State", or refresh the configuration server after...
opened nRF connect and attempted to open the dongle with this. When I plug the dongle in without holding the button, i get this error
2021-02-14T20:18:30.648Z INFO Using...
I am unable to generate setting using nrfutil.
Command used is as follow:
nrfutil settings generate --family NRF52840 --application pca10056/blank/armgcc/_build/nrf52840_xxaa...
Hi
I'm trying to use the LIBUARTE library together with BLE_NUS example in SDK 17.2.
From the libuarte sample I add these lines to NUS example:
I also modify sdk_setup...
Hi!
I am trying to flash some Zigbee related code to experiment with creating DIY smart devices (specifically Zigbee and matter ones) using my Arduino nano 33 BLE. One problem...
Hi,
I flashed open_bootloader and it seams to work. I was following this question . However, after building application (I am using ble_central/ble_app_gatts example), creating...
hi,
im using nrf52811 customised board,for long range purpose im using softdevice s140
so i need to port secure boot loader pca10056 to pca10056e
can you please me reagarding...
Hi,
I have tested the ble_nus code in NCS v1.4.2
where i can't send 250 bytes
I want to send 250 bytes to ble nus data send for 100 ms once
How to enable data send...
Hello,
I use the nrf5340 pdk. I would like to flash the led1 with a duty cycle which is different from 50%, so i tried to open the binky_pwm project, but the segger shows...
