Hello,
I work on a zephyr project with updatable MCUBoot and two updatable images. This configuration ends up with an unbootable image. The reason is that the CONFIG_MCUBOOT_MCUBOOT_IMAGE_NUMBER...
Hello Nordic,
I am working on nRF52832 with SDK 17.1, using ESB, I previously used UART for DFU updates, but now I need to perform OTA updates via ESB.
I noticed a macro...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
Hi,
My nRF5340-DK (serial number 001050065828) suddenly stopped being detected by USB on Windows 11 after months of normal operation. I did not change anything in the hardware...
We are building a line of product to be used in big size building light management and control.
We believe that both the IV values and a huge quantity of SEQ separate counters...
Hello Nordic engineers,
I maintain the lolren/nrf54-arduino-core project: a bare-metal Arduino core for nRF54 boards that deliberately avoids Zephyr and vendor RTOS dependencies...
Dear nordic This ticket is a feature request to implement SSL max_fragment_length of 2k while initiating a TLS connection, when offloading TLS to the NRF9160 modem. As stated...
Hello,
I inserted the following line in the prj.conf file:
CONFIG_I2C = y
done this when I compile I have 7 errors in a code not added by me. the example I'm editing...
Hi,
We got a few boards that have large ADC error. I've already using nrfx_saadc_calibrate_offset to calibrate the offset so I suspect it's caused by gain error. The error...
Hello All,
SDK -- 15.3.0
I want to interface MX25r6435f with NRF52810 so i saw some older queries regarding this Flash driver,
so some where i saw that in sdk QSPI example...
Hi!
We are working with the nrf5340 (custom board-revision QKAAAB) and we are facing an issue when resetting the application. If we add some functionalities to a bluetooth...
hello,
i am using nrf52832 with sdk 15.2 and i want to advertise my beacon like the above picture how can i change the length type and values i can understand the app beacon...
Once paired & Bonding is completed. If neither side pairing & Bonding information is deleted. After restart the device is not advertising again. We are getting PM_EVT_CONN_SEC_FAILED...
Hi, Good afternoon. Some Questions.
1.
Is the Enhanced ShockBurst (ESB) protocol applicable to the nRF5340? I'd appreciate it if you could give me details on how to get...
The nrf52833_peripherals.h file has the P1_PIN_NUM set to 10 but the pca10100.h file has ARDUINO 8-13 pins mapped to port 1, pin 17 to 23. This cannot be correct and causes...
Hey all,
I want to try the Asset Tracker v2 (NCS v1.6.0) Application in AWS, so I followed this guide .
When I try to create the CA certificates and register them in AWS...
Hi,
I'm trying to build the smp_svr example for Thingy:52 but build fails when linking.
I can build for the nrf52dk_nrf52832 which uses the same chip. What can i do to...
Dear Nordic Team,
We have a running product that is using 32KHZ quartz from MicroCrystal : https://www.microcrystal.com/fileadmin/Media/Products/32kHz/Datasheet/CM7V-T1A...
Hello,
I have a design where I am using an nRF52840 along with a SKY66112-11 and am using Zephyr/MPSL for both BLE and Thread. I also have a run-time radio test mode which...
Hi, I have installed the most recent version of nRF toolchain manager for windows (V0.9.2). nRF SDK V1.6.0 was released a couple of days ago but it is (not yet?) in the list...
