I have a nRF54L15 firmware built on NCS v3.0.1, with image encryption enabled in mcuboot. Firmware needs to be updated to new version built on NCS 3.3.0.
In NCS 3.0.1, image...
Hi folks,
I am working on an nRF52840-based custom board using nRF Connect SDK v3.2.4 and have observed an issue related to runtime power management and PWM.
Environment...
Hi, is there a sample using nRF7002 on nRF54LM20B SQSPI (or could you share an appropriate devicetree)? I have been successful using the nRF54LM20 DK + nRF7002 EBII combination...
Hello.
I have nRF52840 USB Dongle connected to PC with nRFConect desktop application 4.0.4
I'm trying to connect to our custom BLE peripheral device, which advertises...
Hi all — I'm developing a custom nRF5340 development board (Raytac MDBT53-1M) and would value the community's honest read on whether it's worth producing.
The goal is...
Hi,
I am using two nRF52833 devices with the nRF5 SDK. They are paired and bonded to each other. Occasionally, I encounter the following error in peer_manager_handler :...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hello all,
I would like to have some help regarding the usage of CoAP protocol. Is there any sample project that supports SDK 17.02 that I can start from?
I am using...
Hi DevZone,
Here's my setup:
Using NRF5 SDK 15.2.0, custom board based on NRF52840
Battery powered device with 3.6V battery.
Supply voltage stepped down to 1.8V...
Good day
Due to I am very new with NRF chips and I did not find direct answer on forum I require some clarification on that moment...
The task is to detect input pulse...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
As mentioned in the DK board User guide nRF52840_DK board is preprogrammed, so, till now we didn't flash the DK board.
I tested the nRF52840_DK board using J2 USB connector...
Hello, with the new version of the nrf5340 version D in the NET CPU RTC0 stops to work and the RTC0 IRQ is not called
now for example the counter is stopped at 87 and the...
Hi,
My problem is that I can't sniff any advertising packet using Wireshark.
I have well followed the detailed procedure https://infocenter.nordicsemi.com/index.jsp...
BLE app uart code write to the BMD 350 device. BLE is disconnected.
If any reasons?
How to configure the TX and RX pins ? when i change the pins, fatal error will come...
Is clearing the NRF_UART_EVENT_RXDRDY really sufficient before exiting the IRQ handler? Since Cortex M4 is used, there's no need to clear the pending register (to avoid the...
Hi, Could you pls check, is it ok if these logs happened?
No firmware defined for selected device Please make sure the device has been programmed with a supported firmware...
Hello
I would like to modify the example "ble_thread_dyn_mtd_coap_cli_nfc" to use Just Works pairing instead of OOB with NFC.
To do this, I modified this in sdk_config...
Hi,
I worked few years ago on a project with the configuration below :
nRF Mesh SDK V1.0.1
nRF52832
I used the light switch example where the client and the provisioner...
Hi, I have built a project upon the aws_iot-example. There are three shadow-topics that the device may publish to (/update, /get and /delete). To me it seems there is no possibility...
