In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
H ello Nordic team,
I'v found a bug on mqtt sample (using both ncs 3.0.0 and 2.6.1).
Description
Settings CONFIG_MQTT_SAMPLE_TRANSPORT_CLIENT_ID and trying to connect...
So, I am adapting and adding to a project based on the example app with SDK16.0 and softdevice s112. I'm using Keil.
My nrf52832 has 256kb flash, 32k ram.
I'm compiling...
Are there any examples of how to configure the COEX pins between the 9160 and a 52840 such that each will actually use the signals to start/stop their respective radios? The...
I see references to a get (0x8046), set (0x8047), and status (0x8048) messages for Node Identity. Where could I find documentation about these messages? There is no sample...
What is the purpose/functionality of SWO pin (pin 6) on the Debug In port?
I see it connected to P0.18 on PCA10040 and P1.00 on PCA10056, but I’m developing custom board...
Hi,
Though I could able to successfully provision light and switch using nrfMesh Android application with all elements being configured and also could publish/subscribe...
Hi,
Recently, I am studying the blog as the link below:
https://docs.microsoft.com/en-us/windows-hardware/design/component-guidelines/bluetooth-prepairing
We would like...
Hi all,
On the iOS version of the Blinky APP, there is a statement
Created by Mostafa Berg on 01/12/2017. Copyright 2017 Nordic Semiconductor ASA. All rights reserved...
Hi,
I am using pin 27 as SCL and 26 as SDA on my custom board which is working on 1.8V.
There is no activity on SCL pin, while i am getting correct values on SDA pin when...
How can I read the ICCID (Integrated Circuit Card ID) of the SIM-card?
Normally (with competitive modems) I get the CCID by AT+CCID.
The nRF9160 reponds with +CME: 0 ...
Hi, I would like to develop a BLE central node that sends over UART when a button is pressed. I understand the memory is limited on nRF52810, but I think it'll fit. The example...
I am developing on the nRF52832. I just discovered that if my program enables Access Port protection by writing the UICR at runtime, then the program can still be read out...
Hello,
I want to use a third party bluetooth module (based on Nordic SOC) in my application, so far my understanding is that using your softDevice stack I have to implement...
Hi
My Thingy:52 works perfectly OK with Thingy app on my iPhone.
However when I use the Gateway on my iPhone and then nrf cloud I get an unstable connection on the cloud...
Hello Developers,
I have just started playing around with BLE Mesh Zephyr examples on my recently purchased nRF52840-PDK board.
Anyways, I am bit stuck with one fundamental...
