I'm working on an open source smart watch project https://github.com/Protocentral/healthypi-move-fw . I'm after serial communication with another device, so I need to re-enable...
HI.
We have experienced an additional power consumption of ~200uA @ 1.8V on our board when booting from PowerOnReset compared to a Warm reset. Searching for the root cause...
Hi, We are in the process of upgrading device firmware (using Nordic nRF9160) from nRF Connect SDK 2.4.2 to nRF Connect SDK 3.4.0 LTS. A number of devices to be upgraded are...
Hi,
Our nRF91 fails to register on LTE-M even though it sees suitable cells and PLMNs. Manual PLMN selection fails as well. The network never sends a reject; the modem seems...
Hello Nordic Semiconductor Support Team,
My name is Marius, and I am the founder of AIDA AS, a Norwegian engineering company working with industrial engineering, HVAC systems...
Dear Nordic Semiconductor Support Team,
I am looking for EasyEDA-compatible schematic and PCB reference design files for the nRF54L15-QFAA .
However, I could not find...
I'm not sure if I can share the files here, but you can email me at kc6ete at gmail if you want a copy It's a four color print designed for the Snapmaker U1 though it can...
Hi.
I am using nRF52840 as a USB mass storage device with SD card. I came across the docs stating that the total number of BULK endpoints available are 14 (7 IN, 7 OUT)...
I have a working code to get FatFs running with SD card over SPI0 interface on a nRF52840 DK. I wanted to know if it is possible to add another SD card with FatFs on SPI2...
Hi,
With the S132 SoftDevice running, is there a way I can ask it to temporarily pause interrupts for a small segment of time so that I can execute extremely time critical...
Hi, The DFU process is working correctly and I've tried downgrading the app version which throws the expected error, so it is stored someplace Accessing via the recommended...
Please tell me everyone's knowledge!
I've seen discussions on smartphones that support "LE Coded PHY", but I'm looking for a tablet size.
Is there any smartphone with...
I'm trying to get my nrf9160 DK to communicate with an i2c device so I setup a project to enable the i2c module and use TWIM to send i2c data. But then I run it and it only...
Hi,
I am using nRF52832 S132 SDK15.2
I am developing an application where the development kit which i am programming is a peripheral.
i want this to connect to specific...
Hey All,
I'm running the LTE Link Monitor on nRF Connect 3.3.3. I'm connecting to my custom nR9160 Feather via the built in USB-to-Serial. I'm able to open the serial port...
I tried to drive MAX30003 to get ECG signals through nrf52832.
I use an analog signal instrument to give the standard ECG signals. Now,the nrf's SPI timing sequence is right...
Hello,
The BLE peripheral I'm developing does not have any specific required connection parameters. I understand that the central ultimately controls the selection of parameters...
Dear
I modify the example of PCA10056 mesh light-server for PCA10059 and it works after I program PCA10059 by nRF Connect –programmer go through USB interface. But there...
Hello,
What is the PPM of LFRC?
In our case, the device will remain in low power mode (System ON, wake up from RTC). The device will wake up at every one hour. Which...
Hello Nordic,
nRF52840, SDK16.0, Softdevice 7.0.1.
I'm using LFCLK to generate an accurate tick for device time keeping (with Prescaler=255, Freq=128Hz, Tick=7.8125ms...
Hi all,
I have a problem when I connect the nRF51822 to my phone.
I use the softdevice S130 and the following code attach .
When I use the nRFconnect in my phone, I...
I have a module BL651 and I want to use it in my dev board. I've found in some previous posts that I have to use nrf52 DK to program externally the nrf52810 in my module....
