Hi, I have to integrate on my MQTT application , location library using GNSS. Actually I am using location library on cellular. I want to use exclusively GNSS. I am developing...
Hi, I am using two nRF54L15 DKs running THroughput samples.
The result of coded s8 is 52kbps, which is close to the theory number.
When I change to S2 code, the result...
I'm moving to 2.9.1 and trying to get mipi working with a st7789 display. I have it working with 2.6.1 without mipi, but can't seem to get it working with mipi on a nrf5340dk...
Hello!
I want to develop a Heartrate Monitor Device which uses BLE and ANT+ using the Seeed XIAO nRF52840 Plus Board.
Now that I have the board I found out that ANT doesn...
Hi
I have one nordic nRF54L15 DK using as peripheral, I want to know the power of it. Thus, I use PPK2 to be a 1.8 voltage source and connect VOUT to P6 pin 1 and GND to...
How do I produce a signed file to flash to the network core for firmware update? I am using a child image/parent concept with the \nrf\samples\ipc\ipc_service\ project, When...
Hello. I am now implementing communication to multiple peripheral devices based on the multi-roll project “ble_app_multirole_lesc”. (image1)
Central link after setting memory...
Hello,
I am developing an app for Android using the Android-nRF-Mesh Library, available here: https://github.com/NordicSemiconductor/Android-nRF-Mesh-Library
According...
Hi everyone,
I use nrf52840 DK with Segger embedded studio. I have created a project where I read several sensors data and send these data to mobile through BLE UART.
...
hi,
is it possible to use a j-link programmer like this one in the photo, to program the adafruit nrf52840 board ? is the development procedures will be same as using a...
I am using s132 v5.1.0 and am in the process of implementing an error-handling architecture.
I'm noticing that much of my error handling could be avoided if there were APIs...
I'm trying to get mcuboot to run on the nRF52840 on the nRF9160 board. I have been able to configure it and get the resulting merged.hex file loaded on the processor and it...
Hello ,
I am using a Laird's BL651 module that has a nRF52810 chipset. I have modified the ble_app_uart example to take a command from Rx characteristic and send a response...
I'm working on IEEE 802.15.4 network using nrf52840 DK boards. I'm making use of the examples in 802.15.4 (secure). I wanted to know how the reception between a transmitter...
I am using SDK v15.3 and modifying the ble_app_uart_c example to setup ble_nus connection between nRF DK board and a custom peripheral. I can use nRF Connect to send and receive...
Hello,
I am using nrf52832 with nrf Mesh DK. Is there a way to unprovision the board from the hardware or command line and not from the app?
Many thanks in advance , ...
Hello , I noticed that my NRF DK advertises for a few minutes and goes back to sleep , because of Advertising Timeout set (I am using the BLE Peripheral Example) , but when...
hello,
I am using SDK v15.2.0,s140,pca100056. In my custom application I am using 3 SPI, RTC, timers, USBD, etc.
Actually during the development stage I have used DEBUG...
Hello,
I am trying to understand the working of BLE Mesh network and have the following question.
Is it possible to make phone as Proxy as well as Provisioner? BLE...
We are planning to build a product based on nRF52811 SoC, which is Bluetooth 5.1 and has AOA and AOD features. Unfortunately, Nordic's hasn't released any new supporting Library...
