Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
We are developing a Bluetooth device around the nRF52840 SoC. The time has come to investigate the production part of things.
Since we have been developing and designing...
Hi Devzone:
Where can I find full document on how to use nrf_power_gpregret_set?
Background: I am planing to do buttonless DFU without BLE but through usb cdc acm.
After...
Dear support team, we are trying to make the device ST IIS2DLPC (accelormeter) talk via SPI to the dev board PCA10040
We are using the evaluation board STEVAL-MKI191V1 wich...
Hello,
I am trying to build the lwm2m_client sample on my ubuntu 16.04 machine. I tried building for nrf9160_pca10090ns and nrf9160_pca20035ns The build fails with:
...
Hi,
I am using SEGGER/SEGGER Embedded Studio for ARM 4.12, I used Two working Examples ble_app_gatts_c_pca10040_s132 and flash_fstorage. I am getting these errors "undefined...
Hello,
For our project I'm using a LIS2DH (accelerometer) that is supposed to trigger an interrupt on its pin INT1 when a movement is detected.
I use nRF52832. Before...
Hi
I'm not familiar with C language, I tested the saadc example in SDK, it worked well in P0.02
But I dont see how they set CH[X].PSELP or CH[X].PSELN (V(p) and V(n))...
Hi
Using PCA 10040A , SDK 16.0.0 and Segger Studio.
I would like to generate a short accurate *** on a GPIO , probably 250 nano seconds duration. So I am looking at using...
Hello All,
my application should record acceleration data and time stamps.
After recording the data block from start to end should be transmitted.
I only know that...
Hello, guys.
In our current project, we need to periodically update AWS IoT Server with the data from local sensors. So far, thanks to the cloud_client example and your...
Hi
For a new project I'm looking for a cheap bluetooth chip. All my software resides in a PIC, because on PIC I have a lot of experience and I don't have the time to dedicate...
Hello all,
I am using NRF52840 and SDK 16 in central mode and added two UUID filters to the scan module for two different groups of peripherals . My application works fine...
Hi,
I am trying to send a test message in Server through mqtt and used the mqtt_simple example for that.
For the test I insert data_publish() function in main() like...
Hi!
The subject is most of the question.
I am beginning to customize the ble_app_template example, and when I build it, connect, and look at the advertising data, I see...
