I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
Hi everyone.
I cutted PCB track shorting solder bridge SB40 .
I connected like this..
Then I opened power profile kit 2. I am using amperemeter..This is my app scrrenshot...
Hi team.
Now i'm use soc nrf5340, and the ncs version 2.9.0.
I want to encrypt my external flash using QSPI.
I encountered some problems while using the nrf connect...
Nordic Support,
My product uses the nRF52840 chip and nRF52 SDK 17.1. I have a feature request to support hosting multiple peripheral connections, each with a unique advertising...
Hello. I'm using the example of the light_switch_server project. I need to configure a server (light bulb) driven by 3 clients (buttons), how can I do? I tried this way, but...
Hello Nordic,
I have to transmit data from the nRF Chip(now i'm testing nRF52832 DK Board) to a PC on UART serial.
Each beacon has transmitted advertising and scanRSP...
Based on the nRF24L01P Product Specification 1.0, after 24L01+ enters into Standby-II state, the only 2 ways to leave this state are 1, set PWR_UP to 0, 2; 2, Feed data into...
I've picked up the DK after a break. Installed the toolchain on my new laptop and was ready to throw the 'blinky' example from the SDK on to it to get started. It did not...
Hi Nordic experts:
I use a device with thingy52-provision-demo firmware(from git-playground), and another device with serial-example to provision the thingy-provision-demo...
Hi.
I want to advertise switching 1Mbit PHY and CodedPHY every 5 seconds.
I designed it like this based on nrf52 ble app uart long range example.
advertising_start(coded...
Is it possible for an app after having gone to sd_power_system_off to reset by button without triggering DFU?
The app seems to need CONFIG_GPIO_AS_PINRESET to be set so...
I am working with production Rev 1 on nrf52840 DK v1.0.0 (2018.19). The spec section 6.35.10.2 Bulk and interrupt OUT transaction say
Until that transfer is finished,...
I am working on mesh application icatin nrf52832 . i want to integrate mesh and nrf sdk application , So i followed this application and mesh_app_uart example Example for...
Hi all,
I am testing DFU example in Mesh SDK . I follow this tutorial : http://infocenter.nordicsemi.com/index.jsp . But when I execute to step 4 :
I get this error...
Hello,
I am new to Nordic products so please apologize me if I am asking a trivial question, but a bit lost on it. I would like to use Thingy 52 board for my project ( I...
Hello,
I am having a trouble with my code. There is an RTC sensor Which has the address 0x32. When the sensor is connected to the TWI lines, there is no problem and it...
Hi There,
I've been developing a product using the NRF52DK. I had some custom PCB's made after I had my circuit designed, and I programmed them with the NRF52DK. Now my...
This one is weird. On a new board with a Rev C '840, when trying to reset the processor using 'nrfjprog --program nuttx.hex --sectorerase --erase', a Decawave DW1000 connected...
