Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
Hi, i am learning with thingy 91 x and nrf9151dk. I made the online courses and succesfully conect to the cloud with the nrf desktop quick start in both devices. Now, i would...
Hello,
I am working with a custom board that has the nRF52840 (via the ISP1807-LR-RS module). This board has the SIT1552AI-JE-DCC-32.768E MEMS TCXO. This TCXO chip has a...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
I am advertising a service and providing scan response data. It is not clear to me whether I should be bothering setting up the values of the ble_adv_modes_config_t structure...
Hi there,
i am very curious about what can be considered as interrupt factor in receiving the signal from beacons, so if these scenarios have been tested please provide...
I'm using the nrf52832-QFAB variant (32K RAM 256K Flash)
The part is marked as NRF52832 QFABB0 1630AC
Surprisingly, this part is happily running my application and bootloader...
Hello,
I can't find where in flash the peer manager data is stored. I'm currently working on DFU support and as part of that I want to define the memory area that should...
As per mesh_hw_resources.md (MESH_SDK/doc/introduction)
## Flash lifetime The flash hardware can withstand a limited number of write/erase cycles. As the mesh stack uses...
Hi all,
I am trying to develop the BLE Heart Rate Collector example on the nrF51 Development Kit. As far as I read in the Nordic web ( http://infocenter.nordicsemi.com/index...
I'm trying develop on a custom board based on the nRF52832 and am running into some issues. When I run the blinky application (with no SD) the application executes fine. However...
Hi I'm developing beacon firmware using ble_app_beacon example code.
I was able to send good beacon data for my purpose. For the next step, I want to turn on the LED which...
Hi,
I am using a custom board based on nRF52 (nRF52832-QFAB-R) and programing it with softdevice.hex and "ble_hid_mouse" example application in the nRF5 SDK v14.2.0. the...
Hi,
I am using softdevice S132 V2.0 for nrf52832 controller.I am using BLE UART app. It is working fine on eval board.But when i checked it on custom board developed by...
Hello,
I am using sdk12.2.2 and nrf52. I have implemented fds_read, fds_write, fds_delete and its working as expected. Now when I am trying to use fds_update my data is...
We are trying \Nordic\nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I want to control UART. If device is not in use i want to...
I'm just starting to bring up a custom board based on the nRF52832 and I am unable to program it using the J-link. It looks like my reset line gets stuck low when the JTAG...
