I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
What would be the best way to plot RSSI levels in dB versus distance using the distance measurement sample code? I see that the default code gives an RSSI open space measurement...
Encountered an issue while programming the nRF5340:
It was working fine before, but after connecting to RTT, a pop-up prompted some encryption option which I didn't read...
Two days ago, I bought a set of ppk2. in the process of use, the host computer software prompts "Device must be programed do you want to procced?", when I click "yes", the...
https://github.com/NordicDeveloperAcademy/ncs-fund/blob/main/v2.9.0-v2.7.0/l4/l4_e1_sol/src/main.c
The current logic uses i and j to calculate factorial.
for (i = 1;...
Hi:
I use sdk nRF5_SDK_17.1.0_ddde560. bootloader use examples\dfu\secure_bootloader\pca10056_uart_debug.
It cann't enter the application.
But If I use examples\dfu...
Hi,
I'm currently trying to write a simple Wi-Fi driver code that can connect to my Wi-Fi network. I'm building for the nrf7002dk_nrf5340_cpuapp and am using NCS v2.5.3...
I want to use the radio test code from the nrf example library to tune the nrf52833 on a custom board. I managed to build and flash the project, but when connecting to the...
Hi,
I have been evaluating some Nordic Semiconductor products for the past week. They look great.
I am using the nRF5340 Dev Kit, along with Visual Studio Code on...
As stated in the title, when I set CONFIG_CHIP_FACTORY_DATA_BUILD to n , the following compilation error occurs.
However, if I keep it as y , the MCU fails to function...
I am measuring latency using the nrf5340_audio with SDK 2.8.0. The measurement points are the analog input on the gateway side and the analog output on the headset side. I...
Hi!
I am using v2.6.1/nrf/samples/bluetoothdirection_finding_connectionless_tx/rx sample, and NCS v2.6.1 for AoA. I made some modification on the rx side to stream I/Q data...
Hi support team,
I'm currently developing a project that requires enabling FCB (for dps to Azure IoT Hub) and LittleFS to store data on an external flash. However I cannot...
academy.nordicsemi.com/.../
The comparison of "increment_count + decrement_count != COMBINED_TOTAL" happens after test_mutex unlock. It is possible that between comparison...
“'\x03\x01\x00\xDB\xDC\x00\x00\xDB\xDD\xFF\xD5\xD1\xC0”An error occurred during the transfer of the bin file, and the packet was returned when the crc was fetched. What should...
