I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hi everyone,
These days I'm evaluating the Nordic nRF5340 to manage audio from two microphones to one dongle station. To achieve this, I configured two nRF5340s as unicast...
I am planning to use 3.7V non Rechargable Battery with Diode and Reverse Protection circuit with npm2100, Would like to build a Fuel Guage model for this as this is not available...
Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
I successfully read accelerometer data at 3000 samples per second . However, when transmitting the data over Bluetooth Low Energy (BLE) , I am only able to send 200 samples...
Is there any pre-existing library similar to the Arduino avdweb_VirtualDelay library available for the Nordic Semiconductor nRF52840 Dongle? I do see the procedure on how...
Hello In SDK 2.6.xx I used to define an extra CMake argument in the VSCode UI, i.e "-DMFG=1" This argument was available when CMakeLists.txt was processed so I could do additional...
We have difficulties to get RTT prints from MCUBoot while performing DFU.
As far as I understand Segger RTT is reinitialized when booting Application and this might be the...
I want to change the bitrate for different settings：
Different settings with 48khz&10ms:
I try ot change the prj.conf to add these:
But an error occurred during...
Hello,
I have a device that I want to operate on the lower range of RSSI (but still around -80dBm and have problems with disconnect. I would like to understand if there...
I want to capture device log. How to capture device log ? Which configuration I need to enable in SDK ? Can you provide sample example which capture device output log ?
We are planning to use NRF52840 for a medical device would like to know from Nordic or anyone from the forum about the verification/validation of SOUP (Software of unknown...
Hi, I am encountering multiple conflicts in the device tree view, which seems quite strange.
"Oscillators" appears to collide with regulator@4000 .
"Clock" appears to...
Hello,
We are in certification stages for our custom product based on the nRF7002DK. Our application requires BLE and WiFi to be operational simultaneously. Consequently...
Hello,
I am new to developing with Nordic products. I have experience working with other microcontrollers like Microchip and STM32. Both of those have their own IDEs. Does...
I would like to integrate System OFF mode of operation into idle system hooks in Zephyr (i.e. when the CPU is idle, it goes into OFF power state automatically). As it currently...
Hi there,
I want to advertise to multiple specific BLE addresses, but I don't know how to implement it with the nRF Connect SDK. Please suggest.
I aim to advertise to...
I am using an nRF52840 and nrf52832 to measure distance, but the reported value is almost twice the actual distance . For example, when the actual distance is 1 meter , the...
Hi,
the nrf45L15 datasheet v0.8 says on page 277 "Note: TWIM and TWIS must use clock pins for both SDA and SCL.".
However in the table 72 on page 795, only the SCL pin...
