Using nRF Connect SDK v3.4.1 with an nRF9151.
CONFIG_NRF_CLOUD_AGNSS currently has unconditional dependencies on:
depends on MODEM_INFO
depends on MODEM_INFO_ADD_NETWORK...
Hi
I am working with nRF Cloud - using a developer account (limited to 10 devices).
After connecting a few times with a device (using a different serial each time),...
I was wondering if the nPM-FG schematic or board design is available, I'm interested in using it to profile a few CR123A's.
The docs suggest the firmware/schematic/layout...
Hi,
On nRF Connect SDK 2.7.0 ( sdk-nrf v2.7.0 , Zephyr v3.6.99-100befc70c74 ), enabling the non-minimal TF-M profile causes WPA2-PSK association to fail during the 4-way...
Hello,
The nrf9160 took over 3 minutes to connect to a cell tower after moving from one country (Singapore, NBIOT) to another (Canada, LTE-M).
After moving, the nrf9160...
Hi Nordic team,
I am testing Channel Sounding on the nRF54L15 using the ras_initiator and ras_reflector samples, and I am seeing a significant difference between measurements...
I have a IMU whose interrupt is connected to GPIO0.11 which is also nrf-gpio-forwarder GPIO (which I dont use)
I managed to get it to work but lost that progress and cant...
Dear Nordic
Question 1: How many bytes can the Rf Tx of the current Nrf52810-QFAA transmit at a time? Now I can only send 256 bytes at a time. Can I send 512 bytes at a...
Hi there,
I always have to start up nrfconnect-5.0.2-x86_64.appimage and then select the power profiler. How can I directly start up the power profiler?
I can see that...
Hi there
I wrote a program (include of advertising, pairing and connecting over service, characteristics) for nrf51822QFAA and work well for C0 build code (nrf51822QFAAC0...
I want to know the power saving mode of nRF5340. Dose this chip set have the following mode ? 1. each BT products connencts, however, the data were not send. above condition...
Today I tried to use the bt_conn_le_param_update() method to update the connection parameters, using the following values.
interval_min = 3000
interval_max = 3000
latency...
Hello,
We can successfully build and flash the ncs/application/asset_tracker_v2 example code in nrf9160. But when trying to boot up, it throws the following error:
**...
Hi there,
I'm using a nRF5340 to generate an 8MHz signal and would like to force the HFXO to always be used as the HFINT is not accurate enough. I have verified this with...
Im following Lesson 8 Exercise 2 – DFU over USB.
My project is in its late stage and now I tried to add DFU over USB but Im getting #error "Serial recovery selected without...
Hi there
My costumer was not able to update the cpunet on a nRF5340.
A lot of troubleshooting now led to the insight, that the costumer used only the app_update.bin...
I had a project that was successfully building in Visual Studio code months ago (June 2024) with Toolchain 2.6.1 for the nRF52832. I have just had time to pick it back up...
Hi Support
I am just checking if Nordic supports hosts other than NRF hosts for the nRF7002 WIFI chip.
I am looking for support for the STM32U5 / STM32H5 mcus - for...
We are develping the BT production by using the Nordic sample program (SampleSoft_NRF5340-AUDIO-DK). ( nRF Connect SDK version is SDK25.0. ) Does this software certify to...
I have a existing design using nrf52810 soc I want send and recieve data using uart --->nrf52810 to nrf52810-->to uart data is custom and have approx 120 bytes, should I send...
I know this exact symptoms has been described many other times, and I apologize. However, I carefully searched through all the previously asked questions in merit and could...
