Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi community I'm trying to evaluate the possibilities of an application update over the air via NB-Iot. According to this post this should be possible.
I'm using the application_update...
Hello Devzone Community,
I am writing to ask whether there is any special or obscure setting (device tree or Kconfig) to enable run-time changes to accelerometer output...
Hi, Nordic engineer!
I am doing the direction finding demos in the nrf52833dk. From previous discussion with you, I learned that with parameter CONFIG_BT_PER_ADV_SYNC_MAX...
Hi support team,
The content of ICHG in Table 22, '1.5 Ω' doesn't match with R_ICHG=1k5 in the corresponding reference circuitry in PS. 1k5 is more likely correct, right...
Hi!
I made same code for SDK15 and it works. Now I want to rebuild project on the new SDK17.0.2 and same part of code doesn't work with SPI master.
For notice- doesn't...
I have seen examples of enabling CCCD by default in the forum but I have not seen anyone say it is not allowed according to the BT SIG.
https://devzone.nordicsemi.com/f...
Hi, I use NRF52833 and SW: NCS version 1.4.1 and its zephyr version is 2.4.0.
I would like to know if there is method to record program counter, stack pointer information...
Hi,
I have used "es_battery_voltage_saadc" in SDK 14.2 to read the voltage of battery, now I'm using SDK 17.02, but there is no es_battery_voltage_saadc.
Is there a better...
Hi
For the revision 3 of the nRF52832, I've updated to the nRF5 SDK V17.1.0 to apply the workaround for erratum 249.
Afterwards, I saw that there is a newer version of...
I have a BLE peripheral device using i2c, gpio. When the peripheral is not connected I want the lowest power consumption possible.
when i try to turn off gpio:
//sleep...
Hi Nordic.
I am using:
1. Mesh sdk V5.00
2. BLE sdk V17
3. NRF52840
I am trying to build a node with many elements and models. The software is based on the LC server...
A question regarding to nRFSDK 1.7: why does nRFSDK disable using BL2 inside TF-M? If our device needs BL2 with TF-M, how can we enable it? I can't enable CONFIG_TFM_BL2 if...
Hi Everyone,
I was wondering if it is something I do wrong, or if there is an issue with my module.
I have never managed to successfully upgrade the firmware of my nRF9160...
Hi,
is it any possibilities to multilink central with s112 in nrf52810 chip?
using sdk: sdk14
actually, i am using sdk14 with one central and one peripheral is fine...
Hello, All,
When using UART on nRF Connect SDK to communicate between nrf9160DK and nRF2833DK, I found that the data length of a packet sent by the UART on both sides is...
