I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hello,
Is it possible to make the nRF Sniffer for Bluetooth LE application work on a nRF54L15?
https://www.nordicsemi.com/Products/Development-tools/nRF-Sniffer-for-Bluetooth...
Hi, I am testing the PaWR examples in the NCS and I have few doubts.
In this page , it says in section 1.3 that there are two ways for synchronization - PAST after connection...
From what I can see in the documentation, UART0 is used by default for "non-secure" / application logs and UART1 is used for "secure" app logs. I am needing to interface with...
Hello, I am using an I2S PDM Mic and trying to send the I2S Data over BLE using Segger Embedded Studio. The I2S Program that I have generated is working ok. I have verified...
I am using SDK 2.9.1. I wanted to follow this tutorial:
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-7-device-driver-model/topic/exercise...
Hello Nordic friends,
currently I use NRF7002-EK successfully in my bare-metal environment, but for debugging, I'm considering using the EB instead of the EK if the edge...
Hi All,
I am currently exploring on nrff4l15 SOC and have its dev kit.
I read on this forum ( multiple tickets ), that there is a support of NSIB. I would like to know...
Hello, I have an application running on an nRF9160. The current app was built using NCS 1.7.0 with the L2M2M Carrier Library enabled. I'm upgrading the application to use...
Hello,
We are developing a Cellular IoT device based on nRF9160 SiP. Essentially it is a battery powered temperature and humiduty sensor, that sends the measurement data...
Hello everyone,
we have an in-house HW with the nPM1300. Both load switches are configured as LDOs as described in datasheet chapter 9.3 configuration 1.
LDO1 is used...
Hi,
I have successfully implement the BLE video transfer using nrf70-wifi-ble-image-transfer-demo .
I can receive the image using the Android-Image-Transfer-Demo application...
I am using VSCode with SDK 2.9.1. I have added the spi21 to the device tree UI editor. When I choose the MOSI, MISO and SCLK, they all show up in the visual representation...
1. Our system is configured with circuit config3 of the nRF52833 WLCSP, where an external power supply of 1.8V is applied to VDD.
Power sequence : USB connection -> VBUS...
Hello,
I'm using the SLM application with an NRF9160. I'm sending AT commands for MQTT publish. After ~10hours the device reboots.
The setup AT commands from powerup...
Zephyr Version 3.7.99, Zeyphr SDK v0.17.0
Thread Version v1.4
Matter SDK Version 1.4
After the switch from Matter SDK version 1.3 to 1.4, the NVS module under Zephyr...
