Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
Using nrf5340 with nrf70 on a custom board, using NCS 2.9.0 (and I can't/won't update to 3.2.x as the nrfx4 update breaks all my code)
I want to use the wifi interface to...
I have an application in which there are two high speed sensors consider it as sensors 1 and sensor 2. Both sensors are connected over same SPI lines having different CS pins...
Hello,
For the vias in the exposed pad of the NRF54L, I've read that ideally, the vias should be capped and filled. However, due to trying to minimize cost, I was wondering...
Hello everyone,
after some months, yesterday I used my PPK2. When I plugged in and I opened the Power Profiler App, a pop up required me to update the device firmware. ...
Hi,
We had a nRF52840 DK board developed off Hardware files v3.0.3 build. The manufacturer didn't have any of the MCU or SEGGER J-Link debugger files on the device. We are...
I added a cmake configuration option to CMakeLists.txt, but sending a value through west build does not set the cmake option. Here is what I have done: CMakeLists.txt
The...
I am using an nRF52840 dongle as a sniffer to capture BLE packets in Wireshark. Recently, I’ve noticed that the captured files are approximately half the expected size, and...
Hello,
my nRF9151 DK appears to be damaged or has a power-path failure.
Current symptoms:
No LEDs light up
No J-Link is detected
No COM port appears
No mass...
I'm stuck implementing encrypted firmwares on the nrf5340, ncs 3.0.2., with NSIB and MCUBoot. I got signed DFU to work as described in Exercise 3 – DFU with external flash...
I noticed from the design guide that the voltage tolerance of capacitors C3 and C10 is 10V. Can I choose 6.3V for the voltage tolerance of these two capacitors? Will this...
I am developing an indoor positioning system using Bluetooth Channel Sounding (CS) on nRF Connect SDK v3.1.1 . My setup involves one Initiator and four Reflectors .
Implementation...
Hi Dev,
Development platform: NRF54L15 + NCS 3.2.3
We are facing an issue with ADC sampling. The code occasionally gets stuck/hangs inside the adc_read function. This...
Hello,
I am currently testing the Release Assistance Indication (RAI) feature on the nRF9151 (SMA-DK) in order to minimize power consumption after data transmission.
I...
Hello, I'm following BLE fundamentals course from Nordic Academy. İn Lesson 4 Exercise 3, with using Nordic UART service. We sent and receive data. However i'm having problem...
Hi everyone. I’m currently working on a custom board based on the nRF5340, but I’m unable to connect to the board when trying to flash it via the SWD interface using J-Link...
