I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
After getting nrf52 board I've sucessfully recovered it, flashed it with blinky example and I cannot recover it again. I tried doing nrfjprog --recover and nrfjprog --family...
I'm working on a custom board that uses an NRF52840, I've followed the Nordic Developer Academy course related to DFU over uart0 ( Exercise 1 - DFU over UART - Nordic Developer...
Hello everyone,
I have a custom board with a nRF5340 on it that is used as a BLE reader for mobile phones. Now we wanted to do some EMC testing. For this we need to broadcast...
I am developing a board with the nrf5340, and using a PDM microphone for audio input.
I have used the same microphone on the nrf52832 with the nrf PDM driver with success...
Hello Nordic team!
I'm currently trying to get a demo of zephyr's Blink up and running on my Thingy53 device so I have an understanding of how the connections between...
Hello,
I’m working on an nRF5340 project and trying to measure power consumption in low power mode using SDK v2.6.1. I followed the instructions provided on your website...
I am developing a code for Nordic nRF52840 with some sensors:
LIS3DH: accelerometer
BME680: environment
Fujitsu MB85RC1M: FRAM
u-blox ZOE-M8: GNSS
SD Card reader...
Hi Team,
I’m currently evaluating the new custom PCB we designed and need to measure its sleep current consumption.
To do this, I plan to create simple firmware for the...
I was messing around with my nrf52832DK and set it to boot mode now the LED5 is flashing continuously, I've tried uploading JLINK firmware into the boot device folder but...
Hello members,
I have problem and got an error below.
============================================================
c:/ncs/toolchains/cf2149caf2/opt/zephyr-sdk/arm-zephyr...
I am now running Ubuntu 22.04.
The following command fails for me:
sudo docker build -t edge-impulse-nordic .
The error is:
Dockerfile:38 --------------------...
Relates to: Thingy91 nRF9160 SDK v2.6.1 I am having trouble successfully extending the size of the tfm partition. I took a sample static partition file from nrf\boards\arm...
I would like for the high duty cycle direct advertising to restart immediately after the ~1.2s timeout.
[I'm using Zephyr. I'm also really new to programming these devices...
Hello, i´m having some problems with the SIM card on my custom NRF9160 board.
if i try to use the AT%XSIM? command to check for the UUIC state i get the following response...
Hi Nordic Community
I was using the nRF Connect Android App to scan the contents of the advertisements sent by my board.
My device is C7:51:E9:6E:C7:43
My question...
