I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
I can't see the answer, so I will write it again.
hello.
nrf24l01p(ptx), nrf51822(prx)
nrf24l01p set
TX_ADDR = 0xA5B300
EN_AA = 0
EN_RXADDR = 1
SETUP_AW =...
Hi, I am trying to add Buttonless DFU functionality to the ble_app_blinky example.
The process I took
1. added the following files to the project
ble_dfu.c ble_dfu_bonded...
Hello, I am trying to implement a basic BLE connection between the nRF52840 Dongle and an Android Device (nRF Connect). I wanted to secure this BLE connection with a passphrase...
Hi everyone,
I am working on buttonless OTA DFU. I have generated my own private and public keys using nrfutil and created the .zip file for DFU.
While generating the...
Using the following image UUID on NRF51822, how do i connect to the host in the nRF5_SDK_12.1.0_0d23e2a softdevice? I used to the example of ..\ble_peripheral\ble_app_uart...
Hi,
I used one nRF52840 dongle and one DK, and placed one sniffer in between to caputure the packets.
The connection interval was set at 7.5 msec, GAP event length is...
I have gone through the nWP-034 document (nRF9160 Hardware Verification Guidelines) and wonder if it exist sample code (firmware) to be used, as a baseline, during regression...
Hi,
we have interfaced Accelerometer Module with NRF52832 using SPI Communication. Psuedo code of code snippet is :
<<Place the snippet here>> Expected : After nrf_spi_transfer...
Hi,
I am trying to use APP_TIMER to detect if a sensor isn't responding to I2C Commands. I created and started the timer with the following steps. The project is based...
I'm using an ISP1807 at 1.8v in a very space constrained and power constrained device.
Is it ok to connect unused pins to GND to make routing easier?
Pins 3, 5, 8, 10...
H,
I am using the SDK 15.0.0 and Segger Embedded Studio for ARM V3.40.
I have been successfully defining a flash memory section for data exchange between the bootloader...
Hi,
I would like to enable the RAI support in the latest master branch of nRF.
Therefore I had a look at the kconfig reference:
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi,
In my current project I have two type of boards. Some have the external 32kHz crystal mounted and some not.
I am trying to detect the presence of the external crystal...
