Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Hi, we are developing a home automation product that needs to support ZigBee. However, at the same time I would like the devices to be able to work with a simple non-mesh...
Hi,
I have a question about bit rates of spis slave (Fspis).What is the minimum bit rates of spis slave? nRF52832 need to communicate with a mcu that it only can work on...
I used a translator. Please understand even if the sentence is weird.
Hi, I used nrf52832 QFAA. (RAM : 64kB, Flash : 512kB)
nrf-intel-hex enabled us to check memory...
Hi,
i want to work with nrf9160 for cloud connectivity, can any one help me providing link for working nrf9160 sdk.suggest me how to build samples without any errors using...
Hi everyone,
I have a weird issue on connexion with my J-link while connecting to my chip. I'm using a NRF52810 which worked very well until now. When I try to connect to...
Hi,
I am using nRF52832 and SDK 16.0.0 with SES.
My project consists in an application that read temperature from a sensor and send it via BLE to another board (no smartphone...
Hi,
I am working on a product based on an nRF52832.
For testing purposes, I have setup the Unity testing framework (using Ceedling).
As soon as a module I want to test...
Hi community ! I'm currently working on mesh, more precisely on nRF52840 device. I archieve to do everything i want with it (combine BLE NUS with MESH). Now, i want to know...
Dear All,
I am using the ble_app_template as my baseline. I have created a custom service with various characteristics and I am able to broadcast my service, connect and...
Our compliance engineers are failing the unmodulated FCC test for our radio because the signal only spans 1MHz, but needs to span 2MHz. We do not have this issue when using...
Hello all,
I'm working on a prototype for a device that simultaneously scans and advertises in certain cases. I have been able to do everything so far except scan by copying...
Hi
I am working with nrf52832 NORDIC soc with Segger with nrf52 sdk 16
I have looked at the "pin_change_int_pca_10040" example and tried to play with it a little bit...
Hi there,
I recently upgraded to nRF Connect for Desktop v3.3.3 and the programmer module to v1.4.2 and I am experiencing the following issues. At first, when I would try...
Hi,
Iam working on a nrf52840 and trying to achieve data flow from BLE device using NUS and transfer this data through UART.Uart is configured as (TX:P1.01,RX:P1.02).Iam...
I am using an nRF52 dev kit. I have loaded the pca_app_hts_pca10040_s132 example into the board. I only added these lines of code
nrf_gpio_cfg_output(ARDUINO_9_PIN); nrf_gpio_cfg_output...
