Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
I've been evaluating the nordic SDK. I was able to install 1.6.1, 1.7.0 numerous times. I've been working with one of the individuals there at Nordic, and I wanted to do a...
The peripheral application I'm working on implements a service which must handle multi-byte incoming messages from a central device and would welcome a pointer to any example...
Hello
I found a possible bug in NCS 1.7.0 which was introduced in PR #5353 .
1) False UNKNOWN event when disconnecting
The "invalid cell id" check leads to an false...
Hey
I'm using the softdevice s140 in my project (and the latest SDK 17.x).
I successfully enable the softdevice and am able to start an advertising (as peripheral). However...
Hi
The baseline current consumption running the azure_iot_hub is very high.
I'm using nRF Connect SDKv1.6.1. The sample connects and sends data to azure as expected. But...
Figure 4: Memory layout
Shows code RAM beginning at 0x0080 0000 but nRF52832 Engineering A Errata 33
"Code RAM is located at address 0x0800_0000".
Additionally 0x2100...
Hi,
I am developing a product based on nrf52840 soc as a central Bluetooth device. I want to connect to a Bluetooth device (as a slave) while it is advertising, but unfortunately...
Hello everyone, i'm trying to run the button sample with Pull_up on the pin P0.27 i did the wiring like below
power->VDD nrf-HV
GPIO->P0.27
i attached a resistance between...
Hi,
Does nRF5340 require any calibration in production line in terms of below items. If so could you share any documents on them
- Gain for the RF front end
- Crystal...
Hi, helpies
I am currently workibg on nrf52832 board and now there are some changes in the hardware and we are left with pin shortage,so we planned to upgrade to nrf52840...
Hi, I am implementing NUS which is based on example BLE_NUS & BLE_NUS_C. The connection is not 1-to-1 but 1-to-7. i.e. 1 Central connects to 7 Peripherals. Although ultimate...
I tried following the " Bluetooth low energy Services, a beginner's tutorial ", I ended up getting stuff to compile and run by making a copy of the ble_app_hrs example, and...
Can I write a J-link flash algorithm by myself? Is there any open source Flash download algorithm for reference? When I call west Flash --recover, I can skip the 4K flash...
Hi,
I am developing a product based on nrf52840 soc as a central bluetooth device. i want to connect nad pair to a bluetooth device (as slave) while it is advertising. ...
