The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hi, when I use OTBR to commission a matter bulb(52840DK), I found this log:
I: 7371 [DL]CHIPoBLE connection established (ConnId: 0x00, GATT MTU: 247) D: 7448 [DL]Indication...
Hi,
I have been trying to use the radio_test example application to try and accomplish my goal but no success so far. My goal is to be able to compose an advertisement packet...
Hello, we would like to use the 4th reference circuit with the QIAA footprint from the Nordic nRF52840 chip's datasheet. However, in our PCB design, can we change the placement...
Hello,
I'm attempting to write to a ble characteristic but when i call bt_gatt_write, I get BT_ATT_ERR_INVALID_ATTRIBUTE_LEN, I have tried to send the same command using...
Question: I am working with the Ebyte E73-2G4M08S1C module, which is based on the nRF52840 . The module provides D+ and D- lines . Can these lines be used for debugging and...
Hello,
I'm trying to put the nRF54L15DK into System Off mode, using sdk & toolchain version v2.8.0.
The provided example (\samples\nfc\system_off) works on my evaluation...
Hello Team, We are currently building a circuit using nRF52833 QDAA QFN40 ( Configuration 5). We would like to know if there are dedicated pins to be configured for BOOT as...
Hi everyone,
I'm working on a Matter based project on the NRF52840 SoC. Since it's an Iot project project we need to reduce power consumption at it's minium for lifetime...
We're starting new medical research project where we have to send data at rate of around 4Mbps from the sensor array for a distance (omnidirectional) of around 2 meters. The...
Good day,
I am learning how to program NRF52832 chips using the NRF52 DK. I am using Segger embeddded v8.2 for the moment as I have not yet learnt how to use the NRF Connect...
Hi,
We have a project based on NRF52811_xxAA_REV1 running on multiple devices without any problem.
Nordic announced recently newer version of SoC (REV2, aka B0) and since...
I have been working on asset tracking v2 application code with thingy91 board, as it is not working. I have updated the modem firmware with latest one (thingy91_mfw-1.3.7_sdk...
Description: I am working with the USB mass storage example provided in github.com/.../mass The example works as expected when built and flashed using NCS v2.6. However, when...
