Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Hi,
I am trying to measure the current of a custom board using PPK board, My custom board takes 5 Volt input supply but PPK board has a 1.8-3.6 Volt external power supply...
I am trying to modify the nRF52840dk_nrf52840 spi_flash sample, ncs/zephyr/samples/drivers/spi_flash , to use dual QSPI.
Following is my device tree configuration:
I...
I am able to pair a peripheral device using advertising 16bit UUID to the Central Device(nRF52840-DK board).
Also I am able to read the Battery level service and Device...
Hi, I have successfully achieved the OTA DFU function on nRF52805. This is what I can see now:
Step 1) I can see the Nordic_Buttonless BLE signal. After connection, there...
When using the nordic power profiler for the nrf52840, it gives the "idle" current as 2.7uA. Presumably this is the deep sleep current, but it seems like this number doesnt...
I've been using nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8 for my development. I'm trying to switch to the nRF connect SDK. I'm having a hard time figuring out where to...
Hi everyone,
So Im trying to modify the event handler of the ATT_MTU example file to have it so that it logs every time a byte is sent / instead of KB but for some reason...
Config options for enabling SDHC card support are not working with nrf SDK V1.6.0. Unable to create the project using Segger IDE.
The same options are used with nrf SDK...
Hello,
We are switching our firmware from the old sdk into the NRFConnect zephyr sdk and I cant see any way to retrieve the channel of the advert when scanning. We need...
Hi everybody,
i've got an issue i want to discuss here. I'm building a webserver using the nRF9160DK with ethernet-shield from PHYTEC and an SD-card which holds the frontend...
Hello,
So I was exploring the nRF52840 DK as a Zigbee device when I found this page: Zigbee CLI wrapper .
This seems very promising, having a python CLI to interface with...
Hello,
I'm doing a project with Zigbee using the nRF52840 and I want to read some sensors that talk via UART.
I have ported with success the nrf_uart example but after...
dear all
Can keil compiled library be used in segger embedded studio? For example, I have a paw8001_ ofn114009_ 12_ m4f_ keil.lib
Library, can I put it directly into NRF...
