I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
we have deploy the serialization libraries in our host to communicate with nrf52840, but it seems the serialization libraries don't handle pairing/bonding event, so we can...
So I am doing a number of crypto operations. One of which for example is an ECDSA signing operation. I do that through mbedtls_ecdsa_write_signature which is using the CC310...
Hello,
We're currently evaluating the feasibility for leveraging our existing NRF51840 as host/system processor that runs all of our application code and runs the BLE...
Hi,
I am having some trouble. For a project, I need GPS, 9 axis IMU (accelerometer, gyroscope, and magnetometer), a microphone, and LTE connectivity in a small form factor...
Hi Team,
I am using nRF Connect SDK v1.3.0 tag for nRF52840 DK.
I am trying to integrate BLE HCI UART project files into Zigbee light switch project.
I have attached...
SDK : nRF5_SDK_for_Thread_and_Zigbee_v4.1.0
Hardware : 2x nRF52840 (PCA10059) + 1x generic overflow sensor.
This is an attempt to gather complete information regarding...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
I am using nRF52832 as central device.
I see from sniffer that LL_VERSION_IND...
I have Power profiler kit 1 which was working fine. I have updated my nrfconnect app and since then on my power profiler kit, I am unable to perform battery power profiling...
Hi
I am trying to build the BLE Secure DFU Bootloader example using SDK 17.02 and the PCA10040 Dev board. Following various threads in the forum, I have been successful...
Hello, I'm trying to merge NFC writeable example " writable_ndef_msg " with BLE Beacon " ble_app_beacon ". My aim is to start BLE Beacon after the scanning of NFC. I have...
Hi.
I have implemented the Central and Peripheral NUS service on two devices(nRF52). Since the central knows the characteristic values, I would like to bypass service discovery...
Hi, I've a timer configured by gpiote to capture with a second 'overflow' capture should the signal stop. I'm not using an interrupt instead the CC[0] value is being used...
I have seen the same issue reported.
nRF52840 DK does not appear as a removable drive named "JLINK"
Done the following.
1- My laptop has only one USB port. So I have...
Hi there, I'm controlling the nrf9160 with a esp32 and I'm wondering if you have an recommended libraries for forming AT commands and parsing the return messages?
